Materiales
Materiales
ISO 4410:2023 - Test methods for the experimental characterization of in-plane permeability of fibrous reinforcements for liquid composite moulding
-
This document specifies test methods for the experimental characterization of in-plane permeability of fibrous reinforcements for liquid composite moulding. Requirements for test equipment,...
ISO 527-4:2023 - Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
-
This document specifies the test conditions for the determination of the tensile properties of isotropic and orthotropic fibre-reinforced plastic composites, based upon the general principles...
ISO 11357-1:2023 - Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles
-
IThe ISO 11357 series specifies several differential scanning calorimetry (DSC) methods for the thermal analysis of polymers and polymer blends, such as— thermoplastics...
ISO 23930:2023 - Fibre-reinforced plastic composites — Full-section compressive test for pultruded profiles
-
This document specifies a method for determining the compressive properties in the pultruded fibre reinforced plastic (FRP) using full-section compressive tests.It is applicable to...
ISO 20975-1:2023 - Fibre-reinforced plastic composites — Determination of laminate through-thickness properties — Part 1: Direct tension and compression tests
-
This document specifies methods for determining the through-thickness properties (i.e. strength, modulus of elasticity, Poisson’s ratio and strain-to-failure) of fibre-reinforced plastic...
ISO 22841:2021/Amd 1:2022 - Composites and reinforcements fibres — Carbon fibre reinforced plastics(CFRPs) and metal assemblies — Determination of the tensile lap-shear strength — Amendment 1: Precision data
-
temtype="https://schema.org/Product" class="section-navigation"> p
ISO 11296-9:2022 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 9: Lining with a rigidly anchored plastics inner layer
-
This document, in conjunction with ISO 11296?1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks...
ISO 22841:2021/Amd 1 - Composites and reinforcements fibres — Carbon fibre reinforced plastics(CFRPs) and metal assemblies — Determination of the tensile lap-shear strength — Amendment 1: Precision data
-
temtype="https://schema.org/Product" class="section-navigation"> u
ISO/TS 23483:2022 - Carbon fibres — Determination of polyacrylonitrile-based (PAN-based) carbon fibre tow characteristics — Heat transfer parameter
-
This document specifies a method using a thermal imaging camera for measuring the heat transfer parameter of PAN-based 12 K carbon fibre tow with a filament diameter of 7 µm. This document...
ISO 24260:2022 - Thermal insulation products — Hemp fiber mat and board — Specification
-
This document specifies requirements for factory-made products of hemp fibre, which are used for the thermal insulation of buildings. This document applies to material containing more than...
ISO/PAS 22101-2:2022 - Polyethylene reinforced with short glass fibres (PE-sGF) piping systems for industrial applications — Part 2: Pipes
-
This document is applicable to short glass fibre reinforced polyethylene (PE-sGF) pipes manufactured by the spiral cross winding method, which are used below ground for the conveyance of liquid...
ISO/PAS 22101-1:2022 - Polyethylene reinforced with short glass fibres (PE-sGF) piping systems for industrial applications — Part 1: General
-
This document specifies the general aspects of short glass fibre reinforced polyethylene (PE-sGF) piping systems, manufactured by the spiral cross winding method, which are used below ground...