Otros
Otros
Mo‐Based Multiphase Interface Design for PcBN Composites: Enhanced Interfacial Bonding, Mechanical, and Cutting Performances
06/09/2026 -
This work adopts cubic press sintering to construct Mo‐derived multiphase interfaces in PcBN. 6 wt% Mo delivers peak mechanical properties, including 1626 MPa flexural strength and 3905 HV...
Manufacturing, Progressive Damage Modeling, and Multiobjective Optimization of 3D Angle‐Interlock Woven Composites Under Tensile Loading
20/08/2026 -
3D angle‐interlock woven composites are fabricated via resin transfer molding, and damage morphologies are examined using scanning electron microscopy. A representative volume element model is...
Effect of the Filler Metal on the Microstructure, Mechanical Properties, and Corrosion Resistance of Inconel 600 Welded Joints Using Gas Metal Arc Welding
02/08/2026 -
Welding of Inconel 600 (IN600) using different filler materials with their proper shielding gases, and gas metal arc welding (GMAW) parameters eases the fabrication of components made by IN600. These...
Experimental and Numerical Evaluation of the Enhancement Effect of Metallic Nanoparticles on Epoxy Composites
30/07/2026 -
This study presents an experimental and numerical evaluation of metallic nanoparticle‐reinforced epoxy composites. The nano‐enhanced systems were characterized through viscosity, mechanical,...
Enhancing Fatigue Crack Growth Resistance in Heterostructured Aluminum Bimetals by Tailored Interface Design
30/07/2026 -
Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link...
Polyaniline‐Modified Carbon Fiber Fabric Electrodes for Epoxy Resin‐Based Multifunctional Structural Supercapacitor Composites
26/07/2026 -
Electrochemical polymerization of polyaniline nanofibers on carbon fiber fabric creates electroactive structural electrodes, enabling epoxy resin‐based structural supercapacitor composites with...
Processing and Characterization of Almond Shell Powder Filled Flax Fiber Reinforced Epoxy Composites
13/07/2026 -
A low cost almond shell filled flax‐epoxy composite is designed and developed for light weight structural and engineering applications.The present‐day demand for environmentally sustainable and...
Strain‐Induced Martensitic Transformation During Uniaxial Tension and Low Cycle Fatigue in a 0.4% C Direct Quenched and Partitioned Martensitic Steel
05/07/2026 -
A 0.4% C steel with 1000+ MPa yield strength and a microstructure with fine lath martensite and film‐like nanoscale retained austenite (RA) undergoes low cycle fatigue—induced martensitic...
Additive Manufacturing of GNP‐Enriched Copper Feedstock via Bound Metal Deposition
22/06/2026 -
A copper–graphene nanoplatelet (Cu–GNP) feedstock was developed and processed via bound metal deposition (BMD) to produce dense copper metallic parts. GNP presence increases the feedstock...
Enhanced Mechanical Performance of 3D‐Printed Continuous Fiber Reinforced Composites Through Nozzle Vibration‐Assisted Compaction
18/06/2026 -
Vibration is conventionally regarded as a source of damage in fiber composites, yet nozzle vibration‐assisted compaction at 50 μm/10 Hz enhances mechanical performance through transient...
Influence of Graphene Oxide Nanoparticles on the Mechanical Behavior of Stereolithography Printed Polyether Ether Ketone Composites
18/06/2026 -
PEEK is blended with graphene oxide (0.25 wt %, 0.50 wt%, and 0.75 wt%), followed by printing by stereolithography to examine the effects of concentration on the microstructure and mechanical...
Laser Power‐Dependent Microstructure Evolution and Wear Behavior of Laser‐Cladded CoCrFeNiAl0.7 High‐Entropy Alloy Coatings
13/06/2026 -
The CoCrFeNiAlx high‐entropy alloy (HEA) system offers high strength, high hardness, and well wear resistance owing to its multiprincipal element composition and special structure. However, the...
Polyimide‐Modified PPTA‐Coated Separator for Lithium Metal Batteries
08/06/2026 -
A novel and low‐cost PPTA‐PI‐coated separator is prepared with a larger internal pore structure in the coating layer. The mechanical strength, ionic conductivity, and Li+ transference were...
Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions
31/05/2026 -
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and...
Enhancement of Corrosion Resistance and Antibacterial Performance of Magnesium Alloys via a Superhydrophobic Cu‐MOFs/CuS Coating
25/04/2026 -
To address the corrosion and microbial adhesion of magnesium alloys in humid, salt‐spray environments, SA‐modified Cu‐MOFs/CuS superhydrophobic coating was fabricated on magnesium alloy via...
Carbon Fiber/Stainless Steel Yarn/Epoxy Hybrid Composites with Highly Mechanical and EMI Shielding Performance
25/04/2026 -
Carbon fiber/stainless steel hybrid composites with laminated, stitched, and woven architectures were developed to achieve both mechanical strength and electromagnetic shielding. The hybrid woven...
Overcoming Mechanical‐Thermal Trade‐Off in Aerogel‐Encapsulated Phase Change Composites via Biomimetic Honeycomb Engineering
11/03/2026 -
Bioinspired honeycomb graphene/calcium alginate aerogel was fabricated via phase‐separation‐based structuring. The precise honeycomb structure enables the aerogel to bear 250,000 times its own...
Tribological and Electrochemical Performance of Ag‐Doped and Undoped Different Ceramic Oxide Coatings Produced by Successive Ionic Layer Adsorption and Reaction on Ti6Al4V‐Extra‐Low Interstitial Alloy Fabricated Using Laser Powder Bed Fusion Additive Manufacturing
05/03/2026 -
Ag‐doped ceramic oxide coatings were synthesized on additively manufactured Ti6Al4V alloys using the cost‐effective SILAR method. The study reveals that Ag incorporation significantly enhances...
Influence of Laser Energy Density on Microstructure Evolution and Mechanical Property of Laser Powder Bed Fusion‐Fabricated B4C/Ti Composites
01/03/2026 -
This study demonstrates the influence of line energy density on the microstructure of B4C/Ti composite materials. Intermediate energy density (0.18–0.24 J/mm2) produces uniform TiB/TiC phases,...
Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue
28/01/2026 -
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and...
Geometric Optimization and Mechanical Performance Enhancement of Auxetic Structures for High‐Impact Applications Through Fused Deposition Modeling
03/01/2026 -
This study explores the mechanical performance of three auxetic structures, identifying a re‐entrant‐star hybrid as the most effective for impact absorption. Finite element simulations and...
