Otros
Otros
ISO 22183:2023 - Plastics — Validation of force-time curves obtained from high-speed tensile tests
-
This document specifies procedures for validation of high-speed tensile test data. It specifies a method to determine the spectrum of the natural oscillation frequencies of the force transducer...
ISO 5430:2023 - Plastics — Ecotoxicity testing scheme for soluble decomposition intermediates from biodegradable plastic materials and products used in the marine environment — Test methods and requirements
-
This document specifies test methods and evaluation criteria by addressing potential ecotoxicological adverse effects on marine organisms. Adverse effects on marine species can be caused by...
ISO 7972:2023 - Adhesives — Absorption of water into an adhesive layer using an open-faced specimen and determination of shear strength by secondary bonding
-
This document specifies a method for the rapid permeation of water to an adhesive layer using a specimen with one side open, the secondary bonding of the specimens with the adhesive layer that...
ISO 8639:2023 - Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness and proof of structural design of flexible joints
-
This document specifies test methods for flexible non-thrust resistant socket-and-spigot joints with elastomeric sealing elements for buried and aboveground glass-reinforced thermosetting...
ISO 24469:2023 - Road wear test of studded tyres
-
This document establishes a test method for evaluating the wear caused to the road surface by passenger car tyres and light truck tyres that are equipped with studs.
ISO 5684:2023 - Adhesives — Floor covering adhesives and products for flooring installation — Assessment and classification of low volatile organic compound (VOC) products
-
This document specifies a reference method for the determination of volatile organic compound (VOC) emissions into indoor air from floor covering adhesives and products used for flooring...
ISO 4907-1:2023 - Plastics — Ion exchange resin — Part 1: Determination of exchange capacity of acrylic anion exchange resins
-
This document specifies test methods of the strong-base group capacity, the weak-base group capacity and the weak-acid group capacity of acrylic anion exchange resins.
ISO 4907-2:2023 - Plastics — Ion exchange resin — Part 2: Determination of water content of anion exchange resins in hydroxide form by centrifugation
-
This document specifies test methods by centrifugation of water content of styrene anion exchange resins in hydroxide form.
ISO 4907-3:2023 - Plastics — Ion exchange resin — Part 3: Determination of exchange capacity of anion exchange resins in hydroxide form
-
This document specifies test methods of the total exchange capacity, the strong-base group capacity and the weak-base group capacity of the styrene anion exchange resins in hydroxide...
ISO 23949:2023 - Plastics — Application of spread of flame test to plastic pipes
-
This document specifies test methods for assessing the flame spread of plastic pipes including fiberglass reinforced plastic (FRP) pipes. This document is applicable to plastic pipes including...
ISO 527-4:2023 - Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
-
This document specifies the test conditions for the determination of the tensile properties of isotropic and orthotropic fibre-reinforced plastic composites, based upon the general principles...
ISO 20567-4:2023 - Paints and varnishes — Determination of stone-chip resistance of coatings — Part 4: Mobile multi-impact testing on a small testing area
-
This document specifies a mobile method for evaluating the resistance of automotive finishes to chilled-iron grit projected onto the surface under test to simulate the effect of stone...
ISO 188:2023 - Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
-
This document specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers/thermoplastic elastomers. Four methods are possible, they are detailed in...
