Otros

 

Otros

The effect of laboratory synthesized and modified layered double hydroxides on recycled and neat high-density polyethylene matrix properties using stearic acid as an interface modifier
02/12/2023 - Abstract This research investigated the effect of layered double hydroxides (LDH) as nanofillers on recycled and neat high-density polyethylene (HDPE) properties. Unmodified and...
Parametric Automated Design and Virtual Simulation of Building Machine Using BIM
01/12/2023 - With the continuous development of the construction technology of the main structure of high-rise buildings, traditional construction techniques have been widely used in high-rise building projects....
Plastic Product Decorating Summit Exceeds Expectations
05/12/2023 - By Jeff Peterson, editor-in-chief, Plastics...
Selective thermal recycling for graphene growth on natural substrates: A comparative study on life cycle assessment, energy consumption, and mechanical performance in recompounding
28/11/2023 - Illustration of the PLA/BR/Clay nanocomposite microstructure alongside the SEM images.AbstractIn this work, several samples based on poly(lactic) acid (PLA)/butadiene rubber (BR) blend with and...
Well-dispersed silica nanoparticle-reinforced epoxy vitrimer composites prepared by dynamic crosslinking
29/11/2023 - Abstract Realizing nano-filler well dispersed in epoxy matrix is essential for the fabrication of high-performance epoxy composites. However, the aggregation of untreated...
Epoxidized canola oil as an environmentally friendly compatibilizer for blending poly(lactic acid) and poly(butylene adipate-co-terephthalate)
30/11/2023 - Abstract Blends of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) are biodegradable polymers with opposite, yet complementary, physical and thermal...
Investigation of Different Features for Baseline-Free RAPID Damage-Imaging Algorithm Using Guided Waves Applied to Metallic and Composite Plates
28/11/2023 - In guided-wave-based damage-imaging algorithms, damage reconstruction typically involves comparing the signals with and without a defect. However, in many cases, defect-free data may not be...
Bio-Based PLA/PBS/PBAT Ternary Blends with Added Nanohydroxyapatite: A Thermal, Physical, and Mechanical Study
30/11/2023 - The physical and mechanical properties of novel bio-based polymer blends of polylactic acid (PLA), poly(butylene succinate) (PBS), and poly (butylene adipate-co-terephthalate) (PBAT) with various...
Recycling of thermoset waste/high?density polyethylene composites: Examining the thermal properties
22/11/2023 - Recycling of thermoset waste/high?density polyethylene composites.In this work, an attempt was made to use recycled thermosetting polymer waste (RTPW) to reduce the environmental impacts. The RTPW...
Magnetic?field?induced Fe3O4@CNTs/PES/SPSf composite membrane for efficient removal of methylene blue by adsorption and catalytic degradation
17/11/2023 - The direct influence of compound compatibility on the permeability of final nanocomposite film.AbstractIn this study, the impact of incorporating a plasticizer on the compatibility between...
Wear Detection of Extruder Elements Based on Current Signature by Means of a Continuous Wavelet Transform
17/11/2023 - Assessing the wear of components in a single-screw extruder and its condition during the process is difficult. In this context, wavelet analysis was used to investigate the wear condition of extruder...
Experimental and application of waste rubber low?temperature green regeneration through ultrasound?assisted method
19/11/2023 - Waste rubber low?temperature green regeneration through ultrasound?assisted method.Combining a traditional mixer and a custom?built ultrasonic generator, low?temperature green regeneration of waste...
Enhancing Thermomechanical Strength and Thermal Stability of Poly(dicyclopentadiene) Composites through Cost-Effective Fly Ash Reinforcement for Structural and Impact Applications
16/11/2023 - Poly(dicyclopentadiene) (poly-DCPD) is a thermoset with potential for high-performance applications. In this research, epoxy resin was blended with different concentrations of fly ash class F...
Influence of Processing Conditions on the Generation of Surface Defects in a Heat-and-Cool Hybrid Injection Molding Technique for Carbon Fiber-Reinforced Thermoplastic Sheets and Development of a Suitable Mold Heated by Far-Infrared Radiation
16/11/2023 - Recently, hybrid injection molding—a type of overmolding technology in which a short carbon fiber-reinforced thermoplastic is injection molded over a compression-molded carbon...
Effect of Alumina on Epoxy Composites with Banana Fiber: Mechanical, Water Resistance and Degradation Property Analysis
11/11/2023 - This ground-breaking research embarks on a journey to explore the transformative capabilities of Musa acuminata fiber-reinforced epoxy composites enriched with the enchanting prowess of...
Enhancing vibration damping properties of MABS/VDT blends using SEBS-g-MAH as a compatibilizer
11/11/2023 - Abstract This investigation focuses on the enhancement of the damping properties of Methyl Methacrylate Acrylonitrile Butadiene Styrene (MABS) through the formulation of a...
Using an Al-Incorporated Deep Black Pigment Coating to Enhance the Solar Absorptance of Iron Oxide-Rich Particles
10/11/2023 - The use of solid particles as direct heat absorbance and storage media promises enhanced storage densities in concentrated solar power (CSP) technologies. The long-term optical performance of those...
Modifications of Phase Morphology, Physical Properties, and Burning Anti-Dripping Performance of Compatibilized Poly(butylene succinate)/High-Density Polyethylene Blend by Adding Nanofillers
13/11/2023 - A twin-screw extruder was used to fabricate poly(butylene succinate) (PBS)/high-density polyethylene (HDPE) blends (7:3 weight ratio) and blend-based nanocomposites. Carbon nanotubes (CNTs), graphene...
A Hybrid Architectural Model for Monitoring Production Performance in the Plastic Injection Molding Process
08/11/2023 - Monitoring production systems is a key element for identifying waste and production efficiency, and for this purpose, the calculation of the Key Performance Indicator (KPI) Overall Equipment...
Cashew Nutshells: A Promising Filler for 3D Printing Filaments
07/11/2023 - Cashew nutshells from the northern region of Colombia were prepared to assess their potential use as a filler in polymer matrix filaments for 3D printing. After drying and grinding processes, cashew...
Efficiency assessment of the SEBS, SEP, and SBS copolymers in the compatibilization of the PS/ABS blend
30/10/2023 - Abstract Polystyrene (PS)/acrylonitrile-butadiene-styrene (ABS) blends were processed in a corrotational twin-screw extruder and molded by injection....