Otros

Otros

Studies on a Novel Jet Mixer in the Extraction Process
02/10/2023 - This paper presents the original results of research on an inline jet mixer being an alternative to other, conventional mixing apparatuses used for extraction processes. In particular, researched...
Highly Efficient and Smallest 76-77 GHz CMOS Transceiver on silicon for Collision Detection in Intelligent Transportation System
29/09/2023 - In recent years, Intelligent Transportation Systems have been universally praised for providing a reliable, comfortable, and safe traffic environment to make automobiles and road traffic...
On the Structural, Thermal, Micromechanical and Tribological Characterizations of Cu-Filled Acrylonitrile Butadiene Styrene Micro-Composites
27/09/2023 - The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper...
Synthesis and characterization of biodegradable and photocrosslinkable multi?block poly(ether?ester): Molecular?weight and component of the polyethylene glycol segment dependence
24/09/2023 - AbstractDue to similar processing and mechanical properties, poly(butylene adipate?co?terephthalate) (PBAT) is expected to be a fully?biodegradable alternative to low?density polyethylene (LDPE)...
Study of the Single-Screw Extrusion Process Using Polylactide
25/09/2023 - This study presents the extrusion process while using a single-screw extruder and polylactide (PLA). This material belongs to the so-called biodegradable plastics, and is characterized by a higher...
Synergistic effect of SiO2 doped g-C3N4 and ammonium polyphosphate on flame retardancy of PA6 composites
20/09/2023 - Abstract The combination of nitrogen and phosphorus compounds has synergistic flame retardant effect, but the addition of low phosphorus content compounds is large, which...
Investigation on the Influence of Process Parameters on the Mechanical Properties of Extruded Bio-Based and Biodegradable Continuous Fiber-Reinforced Thermoplastic Sheets
20/09/2023 - The use of bio-based and biodegradable matrix materials in fiber-reinforced polymers (FRPs) is an approach to reduce the consumption of fossil resources and the amount of polymer waste. This study...
Sintering behavior of ceramic ethylene?propylene?diene rubber/pyrophyllite/zinc borate composites
18/09/2023 - Ceramic polymer materials have great future applications in the field of fireproof materials. However, ceramic polyolefins have shortcomings such as few available inorganic fillers, high sintering...
Characterisation of Curing of Vinyl Ester Resin in an Industrial Pultrusion Process: Influence of Die Temperature
18/09/2023 - Pultrusion is a high-volume manufacturing process for Fibre-Reinforced Polymer (FRP) composites. It requires careful tuning and optimisation of process parameters to obtain the maximum production...
Synthesis and properties of multi?armed polycarboxylate superplasticizer modified by ??cyclodextrin
13/09/2023 - Effectiveness of modified lignin on poly(butylene adipate?co?terephthalate)/poly(lactic acid) mulch film performance.AbstractIn this work, the biodegradable poly(butylene adipate?co?terephthalate)...
Determination of the Size of Complex Iron Oxide Nanoparticles Using Various Physical Experimental Methods
12/09/2023 - A series of organically coated iron oxide nanoparticles obtained via the thermal decomposition of iron–oleate complexes via a “heating-up” process were...
Design and Implementation of an Accessible 3D Bioprinter: Benchmarking the Performance of a Home-Made Bioprinter against a Professional Bioprinter
11/09/2023 - The tremendous application potential of 3D bioprinting in the biomedical field is witnessed by the ever-increasing interest in this technology over the past few years. In particular, the possibility...
Built-Up Fiber-Reinforced Polymers (FRP) Profiles with Improved Shear Performance for FRP–Concrete Hybrid Section
09/09/2023 - Fiber-reinforced polymer (FRP)–concrete hybrid sections, composed of FRP profiles and a concrete slab, have gathered attention in construction due to their lightweight, easy...
Carbon nanotube reinforced biobased poly(urethane urea) covalent adaptable network composite
06/09/2023 - A solvent?free approach was developed to incorporate carbon nanotube (CNT) into castor oil derived poly(urethane urea) (PPU) covalent adaptable network (CAN) based on dynamic piperidine?urea bonds to...
Metal Particle Pencil Beam Spray-Coating Method for High-Density Polymer–Resin Composites: Evaluation of Radiation-Shielding Sheet Properties
06/09/2023 - Medical shielding suits must be lightweight and satisfy the requirements of thin films to guarantee user mobility and safety. The thin film weight is related to the density and thickness, which are...
Non-Isothermal Simulation and Safety Analysis of Twin-Screw Extrusion Process for Synthetizing Energetic Binder Glycidyl Azide Polymer-Based Energetic Thermoplastic Elastomer
05/09/2023 - In order to study the temperature variation and flow characteristics in the twin-screw reactive extrusion process of synthetizing glycidyl azide polymer-based energetic thermoplastic elastomer...
Design of Continuous Kneading System for Active Anode Material Fabrication Using Retrofitted Assembly of Co-Rotating Screw Extruder
05/09/2023 - As the demand for artificial graphite for lithium-ion battery (LIB) anode materials is on the rise, technologies for optimizing the manufacturing processes and reducing the production costs of...
Creep behavior of 3D printed polymer composites
31/08/2023 - Analytical and computational modeling of creep behavior.The creep behavior of polymer composites containing different weight percentages of poly(lactic) acid (PLA), thermoplastic polyurethane (TPU),...
Selective dispersion of SEBS copolymer in the compatibilization of PS/PP recycled copolymer blend: towards the circular economy
30/08/2023 - Abstract The effect of four mixing protocols was investigated in blends of polystyrene (PS) with recycled copolymer polypropylene (PPr), using 10% by weight of...
Prediction of Part Shrinkage for Injection Molded Crystalline Polymer via Cavity Pressure and Melt Temperature Monitoring
31/08/2023 - During an injection molding process, different parts of the molded material are subjected to various thermal–mechanical stresses, such as variable pressures, temperatures, and shear...
Feasibility Analysis of Calcium Carbonate Particle Trajectory Simulation in a Dual Horizontal Shaft Mixer
31/08/2023 - This article aims to investigate the feasibility of using discrete element software EDEM 2022.0 to simulate the trajectory of artificial marble patterns in a dual horizontal shaft mixer. Research was...