Otros

 

Otros

Selective thermal recycling for graphene growth on natural substrates: A comparative study on life cycle assessment, energy consumption, and mechanical performance in recompounding
28/11/2023 - Illustration of the PLA/BR/Clay nanocomposite microstructure alongside the SEM images.AbstractIn this work, several samples based on poly(lactic) acid (PLA)/butadiene rubber (BR) blend with and...
Well-dispersed silica nanoparticle-reinforced epoxy vitrimer composites prepared by dynamic crosslinking
29/11/2023 - Abstract Realizing nano-filler well dispersed in epoxy matrix is essential for the fabrication of high-performance epoxy composites. However, the aggregation of untreated...
Epoxidized canola oil as an environmentally friendly compatibilizer for blending poly(lactic acid) and poly(butylene adipate-co-terephthalate)
30/11/2023 - Abstract Blends of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) are biodegradable polymers with opposite, yet complementary, physical and thermal...
Recycling of thermoset waste/high?density polyethylene composites: Examining the thermal properties
22/11/2023 - Recycling of thermoset waste/high?density polyethylene composites.In this work, an attempt was made to use recycled thermosetting polymer waste (RTPW) to reduce the environmental impacts. The RTPW...
Experimental and application of waste rubber low?temperature green regeneration through ultrasound?assisted method
19/11/2023 - Waste rubber low?temperature green regeneration through ultrasound?assisted method.Combining a traditional mixer and a custom?built ultrasonic generator, low?temperature green regeneration of waste...
Enhancing Thermomechanical Strength and Thermal Stability of Poly(dicyclopentadiene) Composites through Cost-Effective Fly Ash Reinforcement for Structural and Impact Applications
16/11/2023 - Poly(dicyclopentadiene) (poly-DCPD) is a thermoset with potential for high-performance applications. In this research, epoxy resin was blended with different concentrations of fly ash class F...
Influence of Processing Conditions on the Generation of Surface Defects in a Heat-and-Cool Hybrid Injection Molding Technique for Carbon Fiber-Reinforced Thermoplastic Sheets and Development of a Suitable Mold Heated by Far-Infrared Radiation
16/11/2023 - Recently, hybrid injection molding—a type of overmolding technology in which a short carbon fiber-reinforced thermoplastic is injection molded over a compression-molded carbon...
Effect of Alumina on Epoxy Composites with Banana Fiber: Mechanical, Water Resistance and Degradation Property Analysis
11/11/2023 - This ground-breaking research embarks on a journey to explore the transformative capabilities of Musa acuminata fiber-reinforced epoxy composites enriched with the enchanting prowess of...
Using an Al-Incorporated Deep Black Pigment Coating to Enhance the Solar Absorptance of Iron Oxide-Rich Particles
10/11/2023 - The use of solid particles as direct heat absorbance and storage media promises enhanced storage densities in concentrated solar power (CSP) technologies. The long-term optical performance of those...
A Hybrid Architectural Model for Monitoring Production Performance in the Plastic Injection Molding Process
08/11/2023 - Monitoring production systems is a key element for identifying waste and production efficiency, and for this purpose, the calculation of the Key Performance Indicator (KPI) Overall Equipment...
Effects of the injection molding processing settings on the phase morphology and mechanical anisotropy of thermoplastic vulcanizates
26/10/2023 - Flow conditions during the injection moulding of thermoplastic vulcanisates result in the formation of local phase morphology configurations and, consquently, in a mechnical anisotropy, illustrated...
Effect of different modifiers on tobacco stalk fiber/high?density polyethylene composites
20/10/2023 - By utilizing waste tobacco stalks, we have prepared composite materials, achieving their high?value utilization. Additionally, we have successfully improved the performance of the composites by...
Polymeric Materials Obtained by Extrusion and Injection Molding from Lignocellulosic Agroindustrial Biomass
10/10/2023 - This review presents the advances in polymeric materials achieved by extrusion and injection molding from lignocellulosic agroindustrial biomass. Biomass, which is derived from agricultural and...
Studies on a Novel Jet Mixer in the Extraction Process
02/10/2023 - This paper presents the original results of research on an inline jet mixer being an alternative to other, conventional mixing apparatuses used for extraction processes. In particular, researched...
Highly Efficient and Smallest 76-77 GHz CMOS Transceiver on silicon for Collision Detection in Intelligent Transportation System
29/09/2023 - In recent years, Intelligent Transportation Systems have been universally praised for providing a reliable, comfortable, and safe traffic environment to make automobiles and road traffic...
On the Structural, Thermal, Micromechanical and Tribological Characterizations of Cu-Filled Acrylonitrile Butadiene Styrene Micro-Composites
27/09/2023 - The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper...
Sintering behavior of ceramic ethylene?propylene?diene rubber/pyrophyllite/zinc borate composites
18/09/2023 - Ceramic polymer materials have great future applications in the field of fireproof materials. However, ceramic polyolefins have shortcomings such as few available inorganic fillers, high sintering...
Carbon nanotube reinforced biobased poly(urethane urea) covalent adaptable network composite
06/09/2023 - A solvent?free approach was developed to incorporate carbon nanotube (CNT) into castor oil derived poly(urethane urea) (PPU) covalent adaptable network (CAN) based on dynamic piperidine?urea bonds to...
Feasibility Analysis of Calcium Carbonate Particle Trajectory Simulation in a Dual Horizontal Shaft Mixer
31/08/2023 - This article aims to investigate the feasibility of using discrete element software EDEM 2022.0 to simulate the trajectory of artificial marble patterns in a dual horizontal shaft mixer. Research was...
Effect of gamma irradiation on the waste polyethylene/bagasse composites reinforced with flax and sisal fibers for use in wood applications
26/08/2023 - Schematic diagram of wood?composites fabricated by melt mixing processes.Due to their many benefits, including their environmentally benign nature, low cost, biodegradability, and generally good...
Numerical Analysis of Viscous Polymer Resin Mixing Processes in High-Speed Blade-Free Planetary Blender Using Smoothed Particle Hydrodynamics
25/08/2023 - High-speed planetary mixers can rapidly and efficiently combine rheological liquids, such as polymer resins and paste materials, because of the large centrifugal forces generated by the planetary...