Construcción
Construcción
From Phosphor Ceramics to Intelligent Light‐Conversion Materials: High‐Flux Luminescence, Glassy Composite Interface, and Machine‐Learning‐Guided Design
30/09/2026 -
Phosphor ceramics are emerging as robust light‐conversion platforms for next‐generation high‐power LED/LD lighting, laser display, and near‐infrared sources. This review highlights how...
Bioinspired Twisted Brick–Mortar Composites for Adaptive Thermo‐Mechanical Impact Protection
01/10/2026 -
Twisted brick–mortar composites combine a continuously rotated carbon‐nanotube photopolymer framework with a shear‐stiffening gel mortar. The architecture redirects stress waves, promotes crack...
Boosting Chiral Separation Through Sinuous 3D Nanochannels With Saddle–Splay Curvature in Biomimetic Membranes
30/09/2026 -
Self‐assembled polymer membranes featuring double‐gyroid (GYR) nanochannels with continuously varying saddle–splay curvature are developed. The intrinsic negative Gaussian curvature spatially...
Mechanically Robust and Self‐Healing Sustainable Solid‐State Ion‐Conductive Elastomer for Near‐Infrared‐Driven Noncontact Sensing
29/09/2026 -
Mechanically robust and self‐healing sustainable solid‐state ion‐conductive elastomers are developed by constructing a dynamic three‐dimensional interconnected framework within a natural...
Anisotropic Facet Doping Amplifies Built‐In Electric Field in Single‐Particle Photocatalysts
29/09/2026 -
This work proposes a facet‐anisotropic Al doping strategy in single‐crystalline SrTiO3:Al, enabling the creation of an Al‐rich {111}/Al‐poor {100} distribution while preserving predefined...
Seamless Mechanical Programming Through Hybrid Epoxy–Acrylate Printing for Soft–Rigid Robots
29/09/2026 -
Hybrid epoxy‐acrylate printing enables seamless fabrication of soft–rigid robotic systems with covalently integrated interfaces and functionally graded mechanics. Grayscale exposure expands the...
Eucommia Ulmoides Gum‐Inspired Topological Confinement Enables Direct Spinning of All‐Solid‐State Ionic Conductive Elastomers
29/09/2026 -
A Eucommia ulmoides gum (EUG)‐inspired topological confinement strategy is developed to construct all‐solid‐state ionic conductive elastomers featuring a hyperbranched‐nanocluster‐bridged...
Phase‐Confined Ring‐Opening Polymerization Enables Adaptive Wet Adhesion with Dynamic Mechanical Reinforcement
28/09/2026 -
Inspired by hydration‐regulated transitions in snail mucus, liquid–liquid phase separation is harnessed to confine molecular evolution and construct an adaptive double‐network coacervate...
Dual-tetrahedral DNA-enabled strand displacement amplification biosensor for cell imaging and clinical detection of miR-34a-5p in NAFLD
-
The clinical diagnosis of nonalcoholic fatty liver disease (NAFLD) remains challenging due to the invasiveness of liver biopsy and the lack of reliable serum biomarkers, particularly for detecting...
Immobilization of Alginate Microbeads With Whole‐Cells Expressing Nitrilase for Continuous Nicotinic Acid Production in Chip Millireactor
30/09/2026 -
ABSTRACTThe biocatalytic production of nicotinic acid using nitrilases has emerged as a promising alternative to conventional chemical synthesis, offering improved selectivity and environmental...
Dispersoid Refinement and Part Defect Optimization in Additively Manufactured Oxide‐Dispersion‐Strengthened Steels
27/09/2026 -
The characteristics of powders for producing ODS steels through AM are summarized. The possible impacts of powder characteristics on part defects and NPs dispersion are discussed. Some methods...
Evolution of Serrated Flow Behavior Due to Dynamic Strain Aging in High‐Temperature Structural Materials Under Various Cyclic Loading Waveforms
26/09/2026 -
Dynamic strain aging is a material‐dependent (initial microstructure‐dependent) phenomenon in which the stress drop magnitude evolves with progressing fatigue cycles. The minimum limit for the...
3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement
26/09/2026 -
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic...
Interfacial Engineering of Hot‐Pressed Cu–Co–WC Hybrid Composites for Concurrent Hardening, Wear Suppression, and Corrosion Control
24/09/2026 -
Pressure‐assisted hot pressing produces near‐fully dense Cu–Co–WC hybrid composites in which WC provides load‐bearing reinforcement and Co supports matrix–particle continuity. The hybrid...
Fiber‐Format Flexible Linear Electrostatic Motors
27/09/2026 -
A flexible coaxial fibre‐format electrostatic motor enables backdrivable and reversible linear actuation with high force density and functionality under bending, offering a scalable actuation...
Hypertemperature‐Detonated Biomimetic Semiconductor Stromal Bombs for Enhanced Immunotherapy in Pancreatic Cancer
28/09/2026 -
We establish a modular ZIF‐8‐based MOF nanoplatform that integrates NIR‐responsive semiconducting polymer (PCPDTBT) nanoparticles (SPNs) with surface‐grown CuSx NCs and loaded with...
Photon–Phonon–Electron Synergy Enables Efficient Photothermoelectric Conversion for Intelligent Fire Warning
26/09/2026 -
Photothermoelectric detectors are limited by coupled photon–phonon–electron dynamics. We present vertically aligned Ag2Se/Ag‐SPs nanocomposite films via oriented growth and confined phase...
Asymmetric Sulfonated Nanofibrous Separator for Simultaneously Stabilizing Zn Anodes and Accelerating Cathode Kinetics
25/09/2026 -
In this work, we developed an asymmetric SPPS/PP separator to enable stable charging/discharging of practical ZMBs. Benefiting from its asymmetric architecture, the SPPS side facing the cathode...
