Construcción
Construcción
ISO 6076:2023 - Adhesives — Installation of floor coverings, wood flooring, levelling compounds and tiles — Specification of trowel notch sizes
-
This document specifies the individual measurements of notches. It assigns specific codes used to label notched tools according to the measurements and tolerances specified in this...
ISO 24469:2023 - Road wear test of studded tyres
-
This document establishes a test method for evaluating the wear caused to the road surface by passenger car tyres and light truck tyres that are equipped with studs.
ISO 5684:2023 - Adhesives — Floor covering adhesives and products for flooring installation — Assessment and classification of low volatile organic compound (VOC) products
-
This document specifies a reference method for the determination of volatile organic compound (VOC) emissions into indoor air from floor covering adhesives and products used for flooring...
ISO/ASTM 52936-1:2023 - Additive manufacturing of polymers — Qualification principles — Part 1: General principles and preparation of test specimens for PBF-LB
-
This document specifies the general principles to be followed when test specimens of thermoplastic materials are prepared by laser-based powder bed fusion (PBF-LB/P), which is commonly known as...
ISO 24285:2022 - Thermal insulation for building equipment and industrial installations — Cellular glass products — Specification
-
This document specifies the requirements and test methods for factory-made cellular glass products, which are used for thermal insulation of building equipment and industrial installations,...
ISO 29766:2022 - Thermal insulating products for building applications — Determination of tensile strength parallel to faces
-
This document specifies the equipment and procedures for determining the tensile strength of a product parallel to its faces. It is applicable to thermal insulating products.This...
ISO 21634:2022 - Rubber flaps for tyres — Requirements and test methods
-
This document specifies requirements and test methods for tube-type tyres in automotive vehicles that require rubber flaps, in order to ensure they are protected against damages to the inner...
ISO 26986:2010/Amd 1:2022 - Resilient floor coverings — Expanded (cushioned) poly(vinyl chloride) floor covering — Specification — Amendment 1
-
temtype="https://schema.org/Product" class="section-navigation"> p
ISO 11296-9:2022 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 9: Lining with a rigidly anchored plastics inner layer
-
This document, in conjunction with ISO 11296?1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks...
ISO 12623:2022 - Thermal insulating products for building equipment and industrial installations — Determination of short-term water absorption by partial immersion of preformed pipe insulation
-
This document specifies the equipment and procedures for determining the short-term water absorption of preformed pipe insulation by partial immersion in water. It is applicable to thermal...
ISO 18099:2022 - Thermal insulating products for building equipment and industrial installations — Determination of the coefficient of thermal expansion
-
This document specifies the equipment and procedures for determining the coefficient of linear thermal expansion. It is applicable to thermal insulating products within the temperature range...
ISO 12629:2022 - Thermal insulating products for building equipment and industrial installations — Determination of water vapour transmission properties of preformed pipe insulation
-
This document specifies the equipment and procedure for determining the water vapour transmission properties in the steady state under specified test conditions for test specimens of preformed...
ISO 29768:2022 - Thermal insulating products for building applications — Determination of linear dimensions of test specimens
-
This document specifies the characteristics and choice of measuring equipment and the procedure for determining the linear dimensions of test specimens that are taken from thermal insulating...
ISO 18096:2022 - Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature for preformed pipe insulation
-
This document specifies the equipment and procedures for determining the maximum service temperature for preformed pipe insulation. It is applicable to thermal insulating products.
ISO 18097:2022 - Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature
-
This document specifies the equipment and procedures for determining the maximum service temperature of flat insulation products. It is applicable to thermal insulating products.
ISO 18098:2022 - Thermal insulating products for building equipment and industrial installations — Determination of the apparent density of preformed pipe insulation
-
This document specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions. It is applicable to full-size thermal...
ISO/TS 10839:2022 - Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation
-
This document presents a code of practice dealing with polyethylene (PE) pipes and fittings for buried pipeline systems outside buildings, conforming to the ISO 4437 series, and designed to...
ISO 22762-6:2022 - Elastomeric seismic-protection isolators — Part 6: High-durability and high-performance specifications and test methods
-
This document specifies specifications and test methods for elastomeric seismic isolators used for buildings to guarantee high durability and high performance.It is applicable to...