Construcción
Construcción
A Low‐Cost, Open‐Source 3D Printer for Multimaterial and High‐Throughput Direct Ink Writing of Soft and Living Materials
02/01/2025 -
The Printess is a low‐cost, open‐source, multimaterial 3D printer for direct ink writing. Built for under $250, it is highly customizable and supports various advanced direct ink writing...
Soft, Modular Power for Composing Robots with Embodied Energy
02/01/2025 -
A worm‐like robot composed of modular, self‐contained actuators is developed. The modules with embodied zinc‐iodide redox flow batteries are fabricated using a novel bonding method, allowing...
Effect of Density and Thickness of Steel–Steel Composite Metal Foam on Its Full‐Scale Torch Fire Response
23/12/2024 -
Carbon steel calibration steel plate temperature upon 30 min exposure to 1200 °C is reaching well over 700 °C, while a steel composite metal foam (CMF) plate of the same size with 1/3rd of...
Antifouling Immunomodulatory Copolymer Architectures That Inhibit the Fibrosis of Implants
25/12/2024 -
Novel copolymer coatings dramatically reduce the formation of fibrotic tissue on medical implants, extending device longevity. In vivo screening reveals that optimizing copolymer architecture is...
Beyond Fundamental Building Blocks: Plasticity in Structurally Complex Crystals
18/12/2024 -
This study explores how the deformation behavior of intermetallics can be linked through their crystal's building blocks. By examining samarium‐cobalt phases, it is found that their plasticity is...
Lubricated Surface in a Vertical Double‐Sided Architecture for Radiative Cooling and Atmospheric Water Harvesting
18/12/2024 -
A lubricated surface (LS) coating on the condenser side in a vertical double‐sided architecture is used. The design not only effectively doubles the local cooling power, but also eliminates...
Chiton‐Inspired Composites Synergizing Strength and Toughness Through Sinusoidal Interlocking Interfaces for Protective Applications
11/12/2024 -
The chiton Lepidozona coreanica wisely uses the sinusoidal interlocking interface to make up for the short board of the cross‐lamellar structures. Inspired by this, a chiton‐inspired composite...
Adaptive In‐Sensor Computing for Enhanced Feature Perception and Broadband Image Restoration
10/12/2024 -
A novel phototransistor is introduced by leveraging the unique optoelectronic properties of two low‐dimensional materials. The architecture enhances image perception and restoration quality,...
Emerging Sustainable Structural Materials by Assembling Cellulose Nanofibers
10/12/2024 -
Cellulose nanofiber (CNF) has unique intrinsic physical properties, showing great potential for constructing sustainable materials. This review introduces emerging CNF‐based structural materials,...
Electroadhesive Clutches with Enhanced Force Capacity Using Soft Dielectric Interfaces
06/12/2024 -
Soft dielectrics are used to build electroadhesive clutches with high force capacity per contact area but use simple dielectric materials with one‐fifteenth of the permittivity of existing...
Revealing the γ′ and γ″ Phase Fractions of Additively Manufactured and Differently Heat‐Treated Nickel‐Base Superalloy IN718 by Atom Probe Tomography and Their Impact on Mechanical Properties
06/12/2024 -
Additive manufacturing is a promising route for the production of Ni‐base superalloys for turbine applications, such as Inconel 718. Nonetheless, it induces various changes in the microstructure...
Metaplasticity‐Enabled Graphene Quantum Dot Devices for Mitigating Catastrophic Forgetting in Artificial Neural Networks
08/12/2024 -
A two‐terminal metaplastic resistive memory device is developed by combining graphene quantum dots (GQDs) with iron oxide (FeOx). This research contributes to the field of neuromorphic computing by...
3D Nanofabrication via Directed Material Assembly: Mechanism, Method, and Future
02/12/2024 -
Guided material assembly, as an important mechanism of three‐dimensional (3D) nanofabrication, has led to breakthroughs in fabrication resolution, material generality, and throughput, and enabled...
Experimental Study on Mechanical Properties of Cured Sand Combined with Plant-Based Bio-cement (PBBC) and Organic Materials
-
Abstract Bio-cement is a green and energy-saving building material, which has received wide attention in the field of ecological environment and geotechnical engineering in recent...
Exploiting Geometric Frustration in Coupled von Mises Trusses to Program Multifunctional Mechanical Metamaterials
23/11/2024 -
Mechanical metamaterials capable of compressive stiffness tunability, shape morphing, and post‐fabrication modularity. Herein, the 3D unit cell design is based on an assembly of bistable von Mises...
Monolith Catalyst Design by Combining 3D Printing and Atomic Layer Deposition: Toward Green Palladium‐Catalyzed Cross‐Coupling Reactions
21/11/2024 -
This study combines 3D printing and atomic layer deposition to design SiOC ceramic monoliths with palladium nanoparticles, enhancing Suzuki–Miyaura cross‐coupling reactions. The 3D structure...
Characterization, Optimization, and Scaling-up of Submerged Inonotus hispidus Mycelial Fermentation for Enhanced Biomass and Polysaccharide Production
-
Abstract This study was to establish an efficient strategy based on inoculum-morphology control for the submerged mycelial fermentation of an edible and medicinal fungus,...
Sequence and Configuration of a Novel Bispecific Antibody Format Impacts Its Production Using Chinese Hamster Ovary (CHO) Cells
25/11/2024 -
Bispecific BYbe® format sequence and configuration impacts secretory titre. Variable fragment (Fv) sequence and placement can reduce or enhance titre. Vector development strategies that allow tuning...
High?Throughput Multiplexed Plasmonic Color Encryption of Microgel Architectures via Programmable Dithering?Mask Flow Microlithography
20/11/2024 -
This study introduces a scalable method for creating microgel structures with multiplexed hidden plasmonic colors via in situ grown AgNPs in porosity modulated hydrogel network. Utilizing advanced...
Sustainable Smart Packaging from Protein Nanofibrils
20/11/2024 -
Smart packaging can extend shelf life and improve food quality monitoring. This study introduces a novel smart packaging solution using amyloid fibrils and red radish anthocyanins to monitor seafood...
Multifunctional Biocomposite Materials from Chlorella vulgaris Microalgae
19/11/2024 -
A fabrication and post?processing technique is introduced to achieve uniform, lightweight, biocomposites based on C. vulgaris through extrusion 3Dprinting. The bioink formulation and dehydration...
