Envase

Envase

ISO 7765-2:2022 - Plastics film and sheeting — Determination of impact resistance by the free-falling dart method — Part 2: Instrumented puncture test
- This document specifies a test method for the determination of puncture impact properties of a plastic film using instruments for measuring force and deflection. It is applicable if a...
ISO 489:2022 - Plastics — Determination of refractive index
- This document specifies two test methods for determining the refractive index of plastics, namely:—    Method A: a refractometric method for measuring the refractive index of...
F2559/F2559M Standard Guide for Writing a Specification for Sterilizable Peel Pouches has been revised to F2559/F2559M-21
18/11/2021 - Significance and Use 5.1 Medical device peel pouches are universally used by the industry and produced by a myriad of suppliers. They may be constructed of many different...
D4924 Standard Classification for Petroleum Waxes for Use in Rubber Compounding has been revised to D4924-21
18/11/2021 - Significance and Use 4.1 Petroleum waxes in rubber compounds are commonly used to provide protection from degradation by ozone under static conditions, that is, when there is...
D6988 Standard Guide for Determination of Thickness of Plastic Film Test Specimens has been revised to D6988-21
18/11/2021 - Significance and Use 5.1 This guide is intended to provide recommendations and suggested good practices to determine precise dimensions when necessary for the calculation of...
D7310 Standard Practice for Defect Detection and Rating of Plastic Films Using Optical Sensors has been revised to D7310-21
- Significance and Use 4.1 Defects in film are not acceptable to the end-user as there is a reduction in the fitness-for-use in many applications. This document is intended to be...
ISO/TS 21633:2021 - Label-free impedance technology to assess the toxicity of nanomaterials in vitro
01/08/2021 - This document describes a methodology of a label free and real-time detection for non-invasive monitoring of cell-based assays to assess toxicity of nanomaterials to eukaryotic and prokaryotic...
ISO 23517:2021 - Plastics — Soil biodegradable materials for mulch films for use in agriculture and horticulture — Requirements and test methods regarding biodegradation, ecotoxicity and control of constituents
01/07/2021 - This document is applicable to biodegradable plastic materials used to produce mulch films or biodegradable mulch films ready to be used for mulch applications in agriculture and...
D2176 Standard Test Method for Folding Endurance of Paper and Plastics Film by the M.I.T. Tester has been reapproved, available as D2176-16(2021)
- Significance and Use 4.1 The folding endurance is frequently used to estimate the ability of the paper and plastics film to withstand repeated bending, folding, and...
ISO 17555:2021 - Plastics — Film and sheeting — Biaxially oriented polypropylene (PP) films
01/06/2021 - This document specifies the requirements for biaxially oriented polypropylene (PP) films, which are mainly used for packaging. The film can be used alone or in laminates with other...
D2457 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics has been revised to D2457-21
- Significance and Use 4.1 Specular gloss is used primarily as a measure of the shiny appearance of films and surfaces. Precise comparisons of gloss values are meaningful only...
ISO 6452:2021 - Rubber- or plastics-coated fabrics — Determination of fogging characteristics of trim materials in the interior of automobiles
01/05/2021 - This document specifies a test method which is intended to determine the fogging characteristics of rubber- or plastics-coated fabrics that are used as trim materials in the interior of motor...
D2582 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting has been revised to D2582-21
- Significance and Use 4.1 The puncture-propagation of tear test measures the resistance of a material to snagging, or more precisely, to dynamic puncture and propagation of that...
D3420 Standard Test Method for Pendulum Impact Resistance of Plastic Film has been revised to D3420-21
- Significance and Use 5.1 Like other techniques to measure toughness, this test method provides a means to determine parameters of a material at strain rates closer to some...
ISO/TS 21236-2:2021 - Nanotechnologies — Clay nanomaterials — Part 2: Specification of characteristics and measurements for clay nanoplates used for gas-barrier film applications
01/05/2021 - This document specifies characteristics to be measured and measurement methods for clay nanoplate samples in powder and suspension forms used for gas-barrier films. In addition, measurement...
D4300 Standard Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi has been editorially changed, available as D4300-01(2021)e1
- Significance and Use 4.1 These test methods are designed to be used to determine the susceptibility of the adhesive film to biodegradation and whether the adhesive will carry...
D4338 Standard Test Method for Flexibility Determination of Supported Adhesive Films by Mandrel Bend has been reapproved, available as D4338-97(2021)
- Significance and Use 5.1 The mandrel bend test is simple and fast. It requires little investment in equipment and little operator training. The prime purpose is to determine...
ISO 28199-1:2021 - Paints and varnishes — Evaluation of properties of coating systems related to the spray application process — Part 1: Vocabulary and preparation of test panels
01/03/2021 - This document defines terms relating to the evaluation of coating materials in research, development and production with regard to their suitability and safety for industrial processes and...
IEC/TR 63258:2021 - Nanotechnologies — A guideline for ellipsometry application to evaluate the thickness of nanoscale films
01/03/2021 - IEC TR 63258:2021 is a Technical Report focused on the practical protocol of ellipsometry to evaluate the thickness of nanoscale films. This document does not include any specification of the...