Otros

 

Otros

ISO 6806:2024 - Rubber hoses and hose assemblies for use in oil burners — Specification
- This document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.The following two types of hose assembly are specified:—    ...
ISO 4437-5:2024 - Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 5: Fitness for purpose of the system
- This document specifies the requirements of fitness for purpose of assembled polyethylene (PE) piping systems in the field of the supply of gaseous fuels.It specifies the requirements...
ISO 4437-1:2024 - Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 1: General
- This document specifies materials and the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels.It also specifies the test parameters for the...
ISO 4437-3:2024 - Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings
- This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous...
ISO 4437-2:2024 - Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 2: Pipes
- This document specifies the characteristics of pipes made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.It also specifies the test parameters for...
ISO 16422-2:2024 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 2: Pipes
- This document specifies the characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended to be used underground or above-ground...
ISO 16422-5:2024 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 5: Fitness for purpose of the system
- This document specifies the characteristics of the fitness for purpose of oriented unplasticized poly(vinyl chloride) (PVC-O) solid wall piping intended to be used underground or above-ground...
ISO 16422-1:2024 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 1: General
- This document specifies the general characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended to be used underground or...
ISO/TS 16486-7:2023 - Plastics piping systems for the supply of gaseous fuels — Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing — Part 7: Assessment of conformity
- This document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of the ISO 16486 series...
ISO/TS 16422-3:2023 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 3: Fittings
- This document specifies the characteristics of solid-wall oriented unplasticized poly(vinyl chloride) (PVC-O) fittings for piping systems intended to be used underground or above ground where...
ISO 6804:2023 - Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification
- This document specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a...
ISO 23930:2023 - Fibre-reinforced plastic composites — Full-section compressive test for pultruded profiles
- This document specifies a method for determining the compressive properties in the pultruded fibre reinforced plastic (FRP) using full-section compressive tests.It is applicable to...
ISO 4437-4:2022 - Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 4: Valves
- This document specifies the characteristics of valves made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.It is applicable to unidirectional and...
ISO/PAS 22101-2:2022 - Polyethylene reinforced with short glass fibres (PE-sGF) piping systems for industrial applications — Part 2: Pipes
- This document is applicable to short glass fibre reinforced polyethylene (PE-sGF) pipes manufactured by the spiral cross winding method, which are used below ground for the conveyance of liquid...
ISO/PAS 22101-1:2022 - Polyethylene reinforced with short glass fibres (PE-sGF) piping systems for industrial applications — Part 1: General
- This document specifies the general aspects of short glass fibre reinforced polyethylene (PE-sGF) piping systems, manufactured by the spiral cross winding method, which are used below ground...
ISO 9528:2022 - Aerospace — Standard-weight polytetrafluoroethylene (PTFE) hose assemblies, classification 204 °C/21 000 kPa — Procurement specification
- This document specifies requirements for standard-weight polytetrafluoroethylene (PTFE) hose assemblies for use in aircraft hydraulic systems at temperatures between –55 °C and +204 °C...