Otros

Otros

A TRIZ-Supported Concept and Protocol Development for Roof Tile Transportation and Inspection Systems
11/01/2023 - Currently, the use of manual labour in the transportation and inspection systems of leading roof tile manufacturing companies in Indonesia is still prevalent. Manual labour is usually...
Development of Autofeeding Device Applicable to a Biodegradable Pot Tray
07/12/2022 - In this study, a pot autofeeding device for a biodegradable pot tray was developed. The tensile strength and bending strength were measured to identify the physical properties of the biodegradable...
Effects of mechanical recycling on optical properties and microstructure of recycled high?density polyethylene pellets and bottles
26/11/2022 - By introducing aromatic disulfide and designing the synthesis route, we introduce disulfide bonds into the position of the cross?linking point of polyurea and adjust the content of disulfide bonds....
Probabilistic Life Prediction of Tunnel Boring Machine under Wearing Conditions with Incomplete Information
11/11/2022 - This paper developed a data analysis approach to estimate the probabilistic life of an earth pressure balance (EPB) tunnel boring machine (TBM) under wearing conditions with incomplete information....
Solid Particle Erosion Studies of Varying Tow-Scale Carbon Fibre-Reinforced Polymer Composites
27/10/2022 - Solid particle erosion inevitably occurs if a gas–solid or liquid–solid mixture is in contact with a surface, e.g., in pneumatic conveyors. Nowadays, an erosive failure of...
Experimental and application of continuous regeneration of waste rubber
21/10/2022 - Continuous Regeneration of Waste RubberCombined with the Serial Rubber Continuous Mixing Device (SRCMD) and custom?built rotors, the real continuous regeneration of waste rubber was realized. The...
Comparative Experiment of Abrasion-Corrosion-Sliding Wear Performance of Two Kinds of Low Alloy Wear-Resistant Steel
17/09/2022 - There is a serious wear problem in the middle plate of scraper conveyors, which causes the problems of high transportation cost, low efficiency, and a lot of material waste. Therefore, it is...
A TRIZ-Inspired Conceptual Development of a Roof Tile Transportation and Inspection System
15/09/2022 - The Indonesian roof tile manufacturing industry relies heavily on manual operations, specifically in transportation and inspection processes, which creates multiple issues, such as fatigue, injuries,...
Developing a method for evaluating color changeover in a hot-runner multi-cavity injection mold
01/11/2022 - Quality control, which nowadays almost always involves the integration of online measurement methods into the production process, is of paramount importance for injection molding. Online pressure...
Design and Experiment of Nondestructive Post-Harvest Device for Tomatoes
16/08/2022 - This paper proposed a whole process tomato harvester with a nondestructive post-harvest collection operation mode, which was aimed to solve the high damage rate problem during the automatic...
Altering Terahertz Sound Propagation in a Liquid upon Nanoparticle Immersion
14/07/2022 - One of the grand challenges of new generation Condensed Matter physicists is the development of novel devices enabling the control of sound propagation at terahertz frequency. Indeed, phonon...
Cluster-based identification algorithm for in-line recycled concrete aggregates characterization using Laser-Induced Breakdown Spectroscopy (LIBS)
01/10/2022 - To upcycle End-of-Life (EoL) concrete from demolished buildings, it is essential to efficiently identify the different materials that may contaminate it. The precise identification and...
Aerospace, Vol. 9, Pages 293: Influence of Mass Flow Rate on the Atomization Characteristics of Screw Conveyor Swirl Injectors
27/05/2022 - This study conducted cold flow experimental research on the influence of mass flow rate on the atomization characteristics of screw conveyer swirl injectors in an opening environment. The Phase...
High?speed shear dispersion of MWCNTs assisted by PVP in water and its effective combination with wet?mixing technology for NR/MWCNTs nanocomposites
14/04/2022 - 1. High?speed shear dispersion of multi?walled carbon nanotubes (MWCNTs) assisted by polyvinylpyrrolidone in water 2. Wet?mixing technology for natural rubber (NR)/MWCNTs nanocomposites 3. NR/MWCNTs...
Designing of the Electromechanical Drive for Automated Hot Plate Welder Using Load Optimization with Genetic Algorithm
27/02/2022 - Drive and conveyor belts are widely used in the mining and processing industry. One of the types often used is the belt with a cross-section and a diameter of several millimeters, made of weldable...
A Preliminary Studies of the Impact of a Conveyor Belt on the Noise Emission
27/02/2022 - This article performs a comparative analysis of noise generated by conveyor belts with different design parameters. The study was conducted for belts with the same tensile strength, differing in the...
Design, Simulation and Experimentation of a Polythene Film Debris Recovery Machine in Soil
27/01/2022 - With the rapid development of planting techniques using plastic film mulching, the content of residual plastic film in soil increases year by year, which pollutes the soil and water, endangers the...
Artificial Intelligence-Based Real-Time Pineapple Quality Classification Using Acoustic Spectroscopy
18/01/2022 - The pineapple is an essential fruit in Taiwan. Farmers separate pineapples into two types, according to the percentages of water in the pineapples. One is the “drum sound...
Research on On-Line Monitoring System of Hydraulic Actuator of Combine Harvester
24/12/2021 - In view of the complicated hydraulic system, the many driving parts and the great load variation in the combine harvester, and on-line monitoring methods of hydraulic actuating parts such as cutting...