Salud
Salud
Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants
22/04/2026 -
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface...
Influence of Unit Cell Parameters on Mechanical Characteristics of 3D‐Printed Cylindrical Metamaterial Structure: A Finite Element and Experimental Study
18/04/2026 -
This study analyzes how unit cell size affects the mechanical properties of 3D‐printed ABS cylindrical metamaterials. Through experimental testing and simulation, it reveals that width enhances...
2D Materials Enabling Intelligent Multispectral Electromagnetic Responses and Devices
14/04/2026 -
Focusing on the multispectral response mechanisms and devices of 2D electromagnetic materials in microwave‐terahertz‐optical ranges, five key directions are proposed: cross‐domain signal...
Flexible Dielectric Acoustic Resonator Patch for Tissue Regeneration
15/04/2026 -
A flexible dielectric acoustic resonator patch enables MHz‐range ultrasound generation through resonance amplification without using piezoelectric materials. Conformal integration on a curved...
Postoperative feeding practices and nutritional intake in patients with head and neck cancer undergoing surgery with flap tissue transfer reconstruction: a scoping review
16/04/2026 -
Abstract The materials of measurements of long-wave oscillations obtained from a Tsunami Warning Service recorder in the port of Posyet (2013‒2025) and two autonomous stations in...
Multifunctional Ferroelectric Bioelectronic Interfaces for Long‐Term Biosafe Vagus Nerve Modulation
09/04/2026 -
A multifunctional ferroelectric bioelectronic interface (FBI) that integrates self‐rolling for precise geometric matching, robust interfacial adhesion, and neuron‐mimetic polarization‐induced...
Dose-dependent effects of metformin on proliferation and odontogenic differentiation of dental pulp stem cells
13/04/2026 -
HIV disproportionately affects Latino men who have sex with men (LMSM) in the United States (U.S.). Pre-exposure prophylaxis (PrEP) reduces HIV transmission, but prescription and use rates remain...
Dissecting medical referrals in health services: role of physician professional networks
13/04/2026 -
Owing to the high spatiotemporal resolution of light, photocontrol has attracted considerable interest in the field of polymer science. Consequently, various photoreactive moieties that undergo...
Stable Protein‐Based G‐Quadruplex‐Derived Supramolecular Bioinks as Tunable ECM‐Mimetic Constructs Assembled by Combining Non‐Covalent and Covalent Strategies
08/04/2026 -
Harnessing the synergistic interplay of supramolecular self‐assembly, under macromolecular crowding conditions, and enzymatic‐mediated covalent crosslinking toward a stable protein‐based...
Comparison of approaches for quantifying extractables in a variety of polymeric medical device materials with LC-MS/MS
-
Quantification by LC-MS using electrospray ionization (ESI) is challenging due to various factors that influence signal intensity. The gold standard involves the use of isotopically labelled...
Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release
31/03/2026 -
Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and...
Preparation and Characterizations of Antibacterial Iodine‐Containing TiO2 Nanotubes Composite Coatings on Pure Ti
29/03/2026 -
The present study proposes a two‐step electrochemical approach for fabricating iodine‐containing TiO2 nanotubes composite coatings on pure Ti. These coatings not only demonstrate enhanced...
A Water‐Soluble PVA Macrothiol Enables Two‐Photon Microfabrication of Cell‐Interactive Hydrogel Structures at 400 mm s−1 (Adv. Mater. 18/2026)
24/03/2026 -
Two‐Photon Polymerization of HydrogelsTwo‐photon polymerization of hydrogels has been challenged by low writing speeds, partly due to the scarcity of base materials that exhibit sufficient...
Coagulation‐Independent Hemostasis Through Architecturally Programmed Chitosan Aerogels with Dual‐Crosslinked Networks
21/03/2026 -
Hierarchically structured, dual‐crosslinked chitosan aerogels stop severe bleeding even when clotting is impaired. Blood rapidly wicks through aligned pores, unlocking a programmed “elastic...
Graphene Oxide/Copper Modified Polyetheretherketone With Dual Antimicrobial and Osteogenic Activity for Bone Defect Repair
18/03/2026 -
Polyetheretherketone (PEEK) is extensively used in orthopedic implants owing to its excellent mechanical properties and chemical stability. However, its inherent bio‐inertness and lack of...
Recent Advances in the Manufacturing of Furfurylamine Through Biological and Chemobiological Ways
-
Catalytic upgrading of biomass is of paramount importance for the sustainable production of bio-based chemicals and biofuels. The direct use of polysaccharides, such as xylan and glucan, as...
Deployable 3D‐Printed Vascular Stent with Surface‐Catalysed Endogenous Nitric Oxide Generation
15/03/2026 -
A deployable 3D‐printed vascular stent was fabricated with surface‐catalyzed endogenous nitric oxide generation, representing a promising new direction for stent development. The stent can be...
Efficacy and Safety Assessment of 5‐Fluorouracil, Irinotecan and Oxaliplatin‐Loaded Implants in Mouse and Pig Models for Pancreatic Cancer Therapy
15/03/2026 -
A novel FIRINOX‐loaded implant demonstrates controlled drug release, and potent therapeutic efficacy in pancreatic ductal adenocarcinoma mouse models with safety confirmed in a large‐animal...
Poking Pluripotency: Nanoinjection Into Human iPSCs
14/03/2026 -
Nanoinjection into hiPSCs: silicon nanotubes effectively transfect human induced pluripotent stem cells (hiPSCs) with mRNA, enabled by a delayed extracellular matrix application and enhanced surface...
Biofilm‐Antagonist Ginger‐Based 3D‐Printable Photoresins for Complex Implant Designs Exhibiting Advanced Multifunctional Biomedical Applications (Adv. Mater. 15/2026)
13/03/2026 -
Ginger‐Based 3D‐Printed Complex ImplantsIn their Research Article (DOI: 10.1002/adma.202503351), Shady Farah and co‐workers proposed the first‐ever ginger‐based 3D‐printable resin for...
Liquid Touch: Soft and Wearable Vibrotactile Actuators Based on Room Temperature Liquid Metals
09/03/2026 -
A soft electromagnetic vibrotactile actuator based on coils made of room temperature liquid metal driving a small embedded permanent magnet is demonstrated. The resulting actuator remains within safe...
