Inyección
Inyección
ISO 813-2:2024 - Rubber, vulcanized or thermoplastic — Determination of adhesion to a rigid substrate — Part 2: Adhesion of a soft thermoplastic elastomer layer
-
This document specifies a test method for assessing the peel strength of a thermoplastic elastomer (TPE) to a rigid substrate. It is mainly applicable to soft components in the Shore A hardness...
ISO 4981:2023 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Boxes used for retention, detention, storage and transportation systems — Specifications for storm water boxes made of PE, PP and PVC-U
-
This document gives the definitions and specifies the minimum requirements for injection moulded, extruded, compression moulded and thermoformed thermoplastics cuboid shaped boxes, including...
ISO 4982:2023 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Arch-shaped, corrugated wall chambers made of PE or PP used for retention, detention, storage and transportation of storm water systems — Product specifications and performance criteria
-
This document gives the definitions and specifies the minimum requirements for injection moulded and thermoformed thermoplastics corrugated arch-shaped chambers, including integral components,...
ISO 527-4:2023 - Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
-
This document specifies the test conditions for the determination of the tensile properties of isotropic and orthotropic fibre-reinforced plastic composites, based upon the general principles...
ISO 23582-1:2023 - Plastics and rubber machines — Clamping systems — Part 1: Safety requirements for magnetic clamping systems
-
This document specifies the essential safety requirements for the design, the construction and the integration of magnetic clamping systems (MCS) for plastics and rubber machines (e.g....
ISO 19095-5:2023 - Plastics — Evaluation of the adhesion interface performance in plastic-metal assemblies — Part 5: Fracture energy
-
This document specifies a method of testing the adhesion in plastic-metal joints produced by several techniques: adhesive bonding, direct joining of thermoplastics by injection or compression...
ISO 5677:2023 - Testing and characterization of mechanically recycled polypropylene (PP) and polyethylene (PE) for intended use in different plastics processing techniques
-
This document specifies test methods for assessing important properties of mechanically recycled polypropylene [PP (REC)] and polyethylene [PE (REC)] in granular or pellet form for use in...
ISO 13741-1:2023 - Plastics/rubber — Determination of residual monomers and other organic components by capillary-column gas chromatography — Part 1: Direct liquid injection method
-
This document specifies a method for the determination of residual monomers and other (saturated) organic components in aqueous polymer dispersions and latices as well as in related products....
ISO 21634:2022 - Rubber flaps for tyres — Requirements and test methods
-
This document specifies requirements and test methods for tube-type tyres in automotive vehicles that require rubber flaps, in order to ensure they are protected against damages to the inner...
ISO 527-4:2021 - Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
-
This document specifies the test conditions for the determination of the tensile properties of isotropic and orthotropic fibre-reinforced plastic composites, based upon the general principles...
F2803 Standard Test Method for Evaluating Rim Slip Performance of Tires and Wheels has been revised to F2803-21
-
Significance and Use 5.1Â This test method establishes a standard procedure of comparative testing, for driven wheel rim slip, between candidate tire group(s) and a control tire...
D5336 Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials has been revised to D5336-21
-
Abstract This specification covers the classification, testing, and requirements of polyphthalamide (PPA) materials, both virgin and recycled, suitable for injection...
ISO 18804:2021 - Rims for agricultural, forestry and construction machines
01/08/2021 -
This document specifies rim dimensions for rims for agricultural, forestry, and construction machines.
ISO 3739-2:2021 - Industrial tyres and rims — Part 2: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims — Load ratings
01/07/2021 -
This document specifies the load ratings of the metric series of pneumatic tyres primarily intended for industrial vehicles for use on prepared surfaces.ISO 3739-1 deals with...
D3641 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials has been revised to D3641-21
-
Significance and Use 5.1Â It is well known that plastic test specimens molded under different conditions can have significantly different properties. This practice is designed...
D5990 Standard Classification System and Basis for Polyketone Injection Molding and Extrusion Materials (PK) has been revised to D5990-20a
-
1. Scope 1.1 This classification system covers polyketone materials suitable for injection molding and extrusion. This classification system does not address...
F750 Standard Practice for Evaluating Acute Systemic Toxicity of Material Extracts by Systemic Injection in the Mouse has been revised (with title change) to F750-20
-
Significance and Use 4.1 This practice is intended to help assess the biocompatibility of materials used in medical devices. It is an acute toxicological test designed to...
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2020)
15/07/2020 -
This document specifies two two-cavity moulds, the type D11 and D12 ISO moulds, for the injection moulding of small plates measuring 60 mm × 60 mm with a preferred thickness of 1 mm (type...
Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO 20430:2020)
-
This document specifies the essential safety requirements for the design and construction of injection moulding machines for the processing of plastics and/or rubber and provides information for...
