Inyección
Inyección
Co-Injection of Foam and Particles: An Approach for Bottom Water Control in Fractured-Vuggy Reservoirs
22/02/2024 -
Fractured-vuggy carbonate reservoirs are tectonically complex; their reservoirs are dominated by holes and fractures, which are extremely nonhomogeneous and are difficultly exploited. Conventional...
Experimental Study on Optimizing Steam Solvent Co-Injection Process in Akan Carbonate Oilfield
03/02/2023 -
Steam solvent co-injection processes are generating considerable interest in terms of improving heavy oil upgrading in unconventional reservoirs. The characteristics of the opted solvents in the...
The aryl-boron phenolic resins with super ablation properties for resin-transfer molding process of three-dimensional fabric
01/02/2023 -
Boron phenolic resin (BPR) is one of the most extensively utilized matrix resins in ablative field due to its outstanding heat resistance and ablation performance. However, the existing BPR...
CFD study of bio-syngas and coal co-injection in a blast furnace with double lance
15/01/2023 -
To rationally utilize biomass as an auxiliary fuel for pulverized coal injection (PCI) technology, the process of co-injection of bio-syngas/coal into the blast furnace (BF) is designed. In this...
Investigation of Parameter Sensitivity and the Physical Mechanism for the Formation of a Core-Skin-Core (CSC) Structure in Two-Stage Co-Injection Molding
05/11/2022 -
One of the main challenges in co-injection molding is how to predict the skin to core morphology accurately and then manage it properly, especially after skin material has been broken through. In...
Hydrothermal In-Reservoir Upgrading of Heavy Oil in the Presence of Non-Ionic Surfactants
24/10/2022 -
The most widely applied methods to unlock heavy oil and natural bitumen resources in the world are still based on steam injection techniques. Improving the efficiency of hydrothermal processes poses...
Effects of hydrogen fraction in co-injection gas on combustion characteristics of the raceway in low carbon emission blast furnace
-
Co-injection of coal and hydrogen-rich gas with oxygen blast at tuyere is a promising technology for low carbon emission blast furnace ironmaking, which favors the development of hydrogen-based...
Study on co-injection molding of poly(styrene-ethylene-butylene-styrene) and polypropylene: Simulation and experiment
01/04/2022 -
In this paper, poly(styrene-ethylene-butylene-styrene) (SEBS) triblock copolymer blends were used as the soft skin material and polypropylene (PP) was used as the hard core for co-injection...
Investigation on the Fiber Orientation Distributions and Their Influence on the Mechanical Property of the Co-Injection Molding Products
20/12/2019 -
In recent years, due to the rapid development of industrial lightweight technology, composite materials based on fiber reinforced plastics (FRP) have been widely used in the industry. However, the...
Study on Influence of Co-Injection Molding Process on Self-Reinforcing Characteristics of Self-Reinforced Polypropylene Composite via Visualization
02/09/2019 -
Self-reinforced polymer composites (SRCs), which are fabricated by combining the same type of polymer with different properties into one body, have high specific strength, no interfacial...
Reinforcing and toughening isotactic polypropylene through shear-induced crystallization and ?-nucleating agent induced crystallization
25/10/2018 -
In this article, iPP with ?-nucleating agent was molded by sequential co-injection molding (SCIM), in which skin and core melt were injected into the mold cavity one after the other. The...
Gas holdup and liquid velocity distributions in the up flow jet-loop reactor
01/08/2018 -
Hydrodynamics in an up flow jet-loop reactor (JLR) is experimentally investigated. The overall gas holdup, radial and axial distributions of local gas holdup and liquid velocity are presented. A...
