Construcción
Construcción
ISO 16422-2:2024 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 2: Pipes
-
This document specifies the characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended to be used underground or above-ground...
ISO 16422-5:2024 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 5: Fitness for purpose of the system
-
This document specifies the characteristics of the fitness for purpose of oriented unplasticized poly(vinyl chloride) (PVC-O) solid wall piping intended to be used underground or above-ground...
ISO 16422-1:2024 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 1: General
-
This document specifies the general characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended to be used underground or...
ISO 4981:2023 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Boxes used for retention, detention, storage and transportation systems — Specifications for storm water boxes made of PE, PP and PVC-U
-
This document gives the definitions and specifies the minimum requirements for injection moulded, extruded, compression moulded and thermoformed thermoplastics cuboid shaped boxes, including...
ISO/TS 16422-3:2023 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 3: Fittings
-
This document specifies the characteristics of solid-wall oriented unplasticized poly(vinyl chloride) (PVC-O) fittings for piping systems intended to be used underground or above ground where...
ISO 4982:2023 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Arch-shaped, corrugated wall chambers made of PE or PP used for retention, detention, storage and transportation of storm water systems — Product specifications and performance criteria
-
This document gives the definitions and specifies the minimum requirements for injection moulded and thermoformed thermoplastics corrugated arch-shaped chambers, including integral components,...
ISO 22640:2023 - Rubber — Framework for physical and chemical characterization of tyre and road wear particles (TRWP)
-
This document establishes a framework for the characterization of physical and chemical properties of tyre and road wear particles (TRWP) using published analytical standards.It is...
ISO 24469:2023 - Road wear test of studded tyres
-
This document establishes a test method for evaluating the wear caused to the road surface by passenger car tyres and light truck tyres that are equipped with studs.
ISO 21634:2022 - Rubber flaps for tyres — Requirements and test methods
-
This document specifies requirements and test methods for tube-type tyres in automotive vehicles that require rubber flaps, in order to ensure they are protected against damages to the inner...
ISO 11296-9:2022 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 9: Lining with a rigidly anchored plastics inner layer
-
This document, in conjunction with ISO 11296?1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks...
ISO/PAS 22101-2:2022 - Polyethylene reinforced with short glass fibres (PE-sGF) piping systems for industrial applications — Part 2: Pipes
-
This document is applicable to short glass fibre reinforced polyethylene (PE-sGF) pipes manufactured by the spiral cross winding method, which are used below ground for the conveyance of liquid...
ISO/PAS 22101-1:2022 - Polyethylene reinforced with short glass fibres (PE-sGF) piping systems for industrial applications — Part 1: General
-
This document specifies the general aspects of short glass fibre reinforced polyethylene (PE-sGF) piping systems, manufactured by the spiral cross winding method, which are used below ground...
ISO 13268:2022 - Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness
-
This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.
ISO 13267:2022 - Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics inspection chamber and manhole bases — Test methods for buckling resistance
-
This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.
