Automoción

Automoción

ISO 24469:2023 - Road wear test of studded tyres
- This document establishes a test method for evaluating the wear caused to the road surface by passenger car tyres and light truck tyres that are equipped with studs.
ISO 20567-4:2023 - Paints and varnishes — Determination of stone-chip resistance of coatings — Part 4: Mobile multi-impact testing on a small testing area
- This document specifies a mobile method for evaluating the resistance of automotive finishes to chilled-iron grit projected onto the surface under test to simulate the effect of stone...
ISO 20908:2023 - Tyre sound emission test — Methods of drum
- This document specifies methods for measuring tyre-to-road sound emissions from tyres fitted on rig that applies the tyre on a rotating drum under coast-by conditions (i.e. when the tyre is in...
ISO 21634:2022 - Rubber flaps for tyres — Requirements and test methods
- This document specifies requirements and test methods for tube-type tyres in automotive vehicles that require rubber flaps, in order to ensure they are protected against damages to the inner...
ISO 22553-16:2022 - Paints and varnishes — Electro-deposition coatings — Part 16: Pigment-binder ratio
- This document specifies a test method for determining the pigment-binder ratio.It applies to electro-deposition coatings for automotive industries and other general industrial...
ISO 22553-15:2022 - Paints and varnishes — Electro-deposition coatings — Part 15: Permeate residues
- This document specifies a test method for estimating the influence of jetting liquids from the rinsing process after electro-deposition coating (permeate residues) on a coating.It...
ISO 11997-3:2022 - Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 3: Testing of coating systems on materials and components in automotive construction
- This document specifies a method based on a cyclic corrosion test for testing the corrosion protection of automobiles using coating systems on aluminium, steel or galvanized steel.The...
ISO 22553-10:2022 - Paints and varnishes — Electro-deposition coatings — Part 10: Edge protection
- This document specifies a test method for the evaluation of protection against corrosion of edges and stamping burrs by electro-deposition coatings.It applies to electro-deposition...
ISO 15222:2021 - Truck and bus tyres — Method for measuring relative wet grip performance — Loaded new tyres
- This document specifies the method for measuring relative wet grip braking performance index to a reference under loaded conditions for new tyres for use on commercial vehicles on a wet-paved...
F414 Standard Test Method for Energy Absorbed by a Tire When Deformed by Slow-Moving Plunger has been revised to F414-21
- Significance and Use 5.1 This test method establishes a standard procedure of test and provides data that can be related to tire strength, but does not measure tire performance...
F1806 Standard Practice for Tire Testing Operationsâ??Basic Concepts and Terminology for Reference Tire Use has been revised to F1806-21
- Significance and Use 3.1 Tire testing operations usually consist of a sequence of tests that involve special â??referenceâ? tires in addition to the candidate tires being...
F1922 Standard Test Method for Tires, Pneumatic, Vehicular, Highway has been revised to F1922-21
- Significance and Use 4.1 This test method establishes a standard procedure of comparative testing, for tire durability and treadwear, for the use of approving tires under the...
F1923 Standard Test Method for Tires, Pneumatic, Low Speed, Off Highway has been revised to F1923-21
- Significance and Use 4.1 This test method establishes a standard procedure of comparative testing, for tire strength and dimensional characteristics, for use under the...
F2803 Standard Test Method for Evaluating Rim Slip Performance of Tires and Wheels has been revised to F2803-21
- Significance and Use 5.1 This test method establishes a standard procedure of comparative testing, for driven wheel rim slip, between candidate tire group(s) and a control tire...
F408 Standard Test Method for Tires for Wet Traction in Straight-Ahead Braking, Using a Towed Trailer has been revised to F408-21
- Significance and Use 5.1 The measured values are traction properties of tires obtained with the towed trailer described here on a given road surface, under given environmental...
F1046 Standard Guide for Preparing Artificially Worn Passenger and Light Truck Tires for Testing has been revised to F1046-21
- Significance and Use 5.1 Tires having reduced groove depth are required in some tire tests to determine changes in performance as a tire wears in service. This guide describes...
F1572 Standard Test Methods for Tire Performance Testing on Snow and Ice Surfaces has been revised to F1572-21
- Significance and Use 5.1 These test methods describe techniques for assessing the performance characteristics of tires in a winter environment on snow and ice surfaces in a...
ISO 2929:2021 - Rubber hoses and hose assemblies for bulk fuel delivery by truck — Specification
01/09/2021 - This document specifies the requirements for two groups of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of...
ISO 13775-1:2021 - Thermoplastic tubing and hoses for automotive use — Part 1: Non-fuel applications
01/09/2021 - This document specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered by internal-combustion engines, excluding use in air...
ISO 19447:2021 - Passenger car tyres — Method for measuring ice grip performance — Loaded new tyres
01/09/2021 - This document specifies the method for measuring the relative ice grip performance index of a candidate tyre compared with a reference tyre under loaded conditions for new tyres intended to be...