Eléctrico
Eléctrico
ISO/TS 16422-3:2023 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 3: Fittings
-
This document specifies the characteristics of solid-wall oriented unplasticized poly(vinyl chloride) (PVC-O) fittings for piping systems intended to be used underground or above ground where...
ISO 4437-4:2022 - Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 4: Valves
-
This document specifies the characteristics of valves made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.It is applicable to unidirectional and...
ISO/TS 10839:2022 - Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation
-
This document presents a code of practice dealing with polyethylene (PE) pipes and fittings for buried pipeline systems outside buildings, conforming to the ISO 4437 series, and designed to...
ISO/PAS 22101-2:2022 - Polyethylene reinforced with short glass fibres (PE-sGF) piping systems for industrial applications — Part 2: Pipes
-
This document is applicable to short glass fibre reinforced polyethylene (PE-sGF) pipes manufactured by the spiral cross winding method, which are used below ground for the conveyance of liquid...
ISO 13844:2022 - Plastics piping systems — Elastomeric-sealing-ring-type socket joints for use with plastic pipes — Test method for leaktightness under negative pressure, angular deflection and deformation
-
This document specifies a method for testing the leak tightness under negative pressure, angular deflection and deformation of assembled joints between elastomeric-sealing-ring-type sockets...
ISO 16486-4:2022 - Plastics piping systems for the supply of gaseous fuels — Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing — Part 4: Valves
-
This document specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous...
ISO 27126:2021 - Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals — Specification
01/11/2021 -
This document specifies requirements for four types of thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for carrying hydrocarbons, solvents and chemicals. It specifies bore...
F2754/F2754M Standard Test Method for Measurement of Camber, Cast, Helix, and Direction of Helix of Coiled Wire has been revised to F2754/F2754M-21
-
Significance and Use 4.1Â The process of coiling wire causes the wire to take on a curvature from the process of being mechanically deformed into a coiled geometry. The...
ISO 23384:2021 - Rubber and plastics hoses and hose assemblies, wire or textile reinforced types with working pressure equal or above 70 MPa (700 bar) — Specification
01/04/2021 -
This document specifies requirements for two types of reinforced hoses and hose assemblies of nominal size from 3,2 to 25, dependent on relation of minimum burst pressure to maximum working...
Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 5: Cut steel wire (ISO 11124-5:2019)
-
This document specifies technical requirements for steel cut wire shot abrasives in 13 kinds of specifications and grades including hardness, apparent density, defect, metallographic structure and...
F2229 Standard Specification for Wrought, Nitrogen Strengthened 23Manganese-21Chromium-1Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29108) has been revised to F2229-21
-
Abstract This specification covers the chemical, mechanical, and metallurgical requirements for wrought, nitrogen strengthened manganese-chromium-molybdenum low-nickel...