Industria 4.0
Industria 4.0
A Review on Microstructure and Magnetic Property Control in Additively Manufactured Magnetic Materials
09/05/2026 -
This review examines microstructure control and magnetic property optimization in additively manufactured magnetic materials, focusing on soft and hard alloys, processing routes, and field‐assisted...
Reactive Laser Additive Manufacturing of Hierarchically Structured Aerogels
08/05/2026 -
Reactive laser additive manufacturing transforms printing into a chemically active synthesis step. Salt‐enabled transient reaction environments drive in situ formation of hierarchically structured...
Two‐Photon 3D Printing of Functional Microstructures Inside Living Cells (Adv. Mater. 25/2026)
04/05/2026 -
Two‐Photon 3D Printing of Functional MicrostructuresVarious polymer microstructures, including an elephant, are printed inside living cells. An injected droplet of biocompatible photocurable...
Bulk Metallic Glass and Composites with Flexible Processing Windows
30/04/2026 -
Microstructure analysis of suction cast [Ti35.1Zr32.7Nb3.8Cu10.3Be17.5Sn0.6] showing crystalline dendrites surrounded by the amorphous matrix and transmission electron microscopy (TEM) energy...
Recent Advances in 3D‐Printed Multifunctional Thermally Deformed Metamaterials
29/04/2026 -
This review summarizes recent advances in 3D‐printed multifunctional thermally deformed metamaterials. By integrating thermal expansion regulation with Poisson's ratio control, stiffness...
Additively Manufactured Soft Magnets With Reduced Core Loss
29/04/2026 -
Soft magnetic toroids are fabricated from Ancorsteel and FeSi3.5wt% using laser powder bed fusion metal additive manufacturing. The cross‐sections of the magnetic toroids consist of Hilbert and...
Experimental Study on Sound Absorption of Triply Periodic Minimal Surface With Porous Fillings
28/04/2026 -
Triply Periodic Minimal Surface (TPMS) structures filled with foam or aerogel significantly enhance broadband sound absorption. Foam‐filled TPMS performance is sensitive to structural parameters...
Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability
27/04/2026 -
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article...
Validation of Profilometry‐Based Indentation Plastometry (PIP) Testing for Rapid Qualification of Electron Beam‐Powder Bed Fusion (EB‐PBF) With Ti–6Al–4V Builds
27/04/2026 -
Focusing on advanced materials produced by a new electron beam powder bed fusion (EB‐PBF) system, this work combines innovative rapid mechanical characterization techniques at high temperatures and...
In Situ Mullite Toughening of Zirconia‐Toughened Alumina Ceramics via Digital Light Processing 3D Printing
26/04/2026 -
Mullite‐toughened ZTA ceramics fabricated via DLP 3D printing exhibited optimal mechanical properties with the addition of 3 wt% SiO2, showing a hardness of 16.2 GPa, a flexural strength of 463.8...
Design and Finite Element Modeling of 3D‐Printed Porous Metamaterial Beam Cores for Hybrid Bone Plates
25/04/2026 -
A hybrid triply periodic minimal surface beam‐core bone plate is investigated as an architecture‐driven strategy for stiffness modulation and load sharing. Experimental bending tests, analytical...
Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties
24/04/2026 -
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while...
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
24/04/2026 -
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by...
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
24/04/2026 -
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is...
The Resolution–Throughput Conflict In Material Extrusion Additive Manufacturing
23/04/2026 -
Extrusion‐based additive manufacturing is widely used but fundamentally constrained by a tradeoff between feature resolution and fabrication throughput. This perspective analyzes the coupled...
Production of MgO/TiC Composites From MgO‐C Recyclates Using Spark Plasma Sintering
22/04/2026 -
Using the spark plasma sintering technique, MgO/TiC composites are manufactured from recycled MgO‐C refractories stemming from the steel production that were mixed with titanium powder. This...
Self‐Supporting 3D Boron‐Based Photocatalyst Prototype for Water Treatment
22/04/2026 -
Schematic workflow illustrating the fabrication process of 3D PhC, encompassing starting material, stereolithographic 3D printing, annealing, and application in solar water treatment. The...
Influence of Unit Cell Parameters on Mechanical Characteristics of 3D‐Printed Cylindrical Metamaterial Structure: A Finite Element and Experimental Study
18/04/2026 -
This study analyzes how unit cell size affects the mechanical properties of 3D‐printed ABS cylindrical metamaterials. Through experimental testing and simulation, it reveals that width enhances...
