Industria 4.0
Industria 4.0
Polymorphing Hydrogels Regulated by Photo‐reactive DNA Cross‐links
01/12/2024 -
Photo‐reactive DNA‐cross‐linked hydrogels are presented that enable polymorphing under patterned light. The photo‐reactive DNA crosslinks act as a regulator in morphing of the hydrogels,...
Impact of Infill Density and Glass Fiber Reinforcement on the Compressive and Bending Strength of Acrylonitrile Butadiene 3D‐Printed Corrugated Sandwich Panels
27/11/2024 -
This study introduces a novel approach in additive manufacturing for creating high‐strength, lightweight corrugated sandwich panels with acrylonitrile butadiene styrene‐reinforced by glass...
A Review on Corrosion Behavior and Surface Modification Technology of Nickel Aluminum Bronze Alloys: Current Research and Prospects
27/11/2024 -
The current review gives the progress on the corrosion behaviors and corrosion mechanism of nickel aluminum bronze and systematically discusses the research status of the surface modification...
Monolith Catalyst Design by Combining 3D Printing and Atomic Layer Deposition: Toward Green Palladium‐Catalyzed Cross‐Coupling Reactions
21/11/2024 -
This study combines 3D printing and atomic layer deposition to design SiOC ceramic monoliths with palladium nanoparticles, enhancing Suzuki–Miyaura cross‐coupling reactions. The 3D structure...
Harnessing Extrinsic Dissipation to Enhance the Toughness of Composites and Composite Joints: A State?of?the?Art Review of Recent Advances
20/11/2024 -
This review highlights how toughness of laminated structures can be manipulated by engineering heterogeneity and microstructure of interfaces, bond lines and substrates. These techniques favor...
Heterogeneous Deformation of As-Built Nickel Alloy 625 with Checkered Columnar Grains at Different Strain Rates (AMB2022-04)
20/11/2024 -
Abstract The Additive Manufacturing Benchmark Test Series (AM Bench) provides comprehensive measurement data for additive manufacturing (AM) simulations and modeling. As part of...
Effect of CuO nanoparticle size distribution on Cu-based patterns fabricated via femtosecond laser-pulse-induced thermochemical reduction
19/11/2024 -
Abstract Copper-direct writing using laser reductive sintering of CuO nanoparticles has received significant interest for printing technology. We investigated the effect of the...
Y-Gd-Zn tri-doped BaCeO3-BaZrO3 proton conducting electrolytes with improved electrical and transport properties
20/11/2024 -
Abstract In this study, the BaCeO3-BaZrO3 material was modified using an internal addition method of ZnO as a sintering aid. resulting in the synthesis of the Zn, Y and Gd...
Optimizing Renewable Energy Systems Placement Through Advanced Deep Learning and Evolutionary Algorithms
21/11/2024 -
As the world shifts towards a low-carbon economy, the strategic deployment of renewable energy sources (RESs) is critical for maximizing energy output and ensuring sustainability. This study...
The Impact of BIM Technology on the Lifecycle Cost Control of Prefabricated Buildings: Evidence from China
21/11/2024 -
Prefabricated construction has become a significant trend in the international building industry, yet its promotion in China faces cost challenges. This study explores the effect of building...
A Study on the Factors Influencing Willingness to Use Virtual Reality Systems for External Evaluation of Buildings
21/11/2024 -
Integrating new visualization methods based on virtual reality (VR) in the design evaluation process remains a challenge despite its expanding use in architectural design in recent years. This...
Multiple Preheating Processes for Suppressing Liquefaction Cracks in IN738LC Superalloy Fabricated by Electron Beam Powder Bed Fusion (EB-PBF)
20/11/2024 -
In additive manufacturing, controlling hot cracking in non-weldable nickel-based superalloys poses a significant challenge for forming complex components. This study introduces a multiple preheating...
Microstructure and Hardness of Nickel-Based Coatings Prepared by Laser Additive Manufacturing on Water-Cooled Substrate: An Experimental and Numerical Study
21/11/2024 -
The excess heat generated during the laser additive manufacturing process is prone to cause coating defects; a water-cooled substrate can effectively remove the excess heat and improve the hardness...
Optimizing Waste Sorting for Sustainability: An AI-Powered Robotic Solution for Beverage Container Recycling
21/11/2024 -
With Japan facing workforce shortages and the need for enhanced recycling systems due to an aging population and increasing environmental challenges, automation in recycling facilities has become a...
The Torsional Characterization of 3D?Printed Polylactic Acid Parts With Alternating Additive Manufacturing Parameters
18/11/2024 -
ABSTRACTThree?dimensional (3D) printed polymer parts can be subjected to torsional loads in accordance with the conditions of use. Understanding the torsional properties of 3D printed polymers...
Promoting Piezoelectricity in Amino Acids by Fluorination
17/11/2024 -
A high piezoelectric amino acid (Cbz?Phe(4F)) is designed by simple fluorination. Cbz?Phe(4F) self?assembles into single crystals with C2 space group. Importantly, Cbz?Phe(4F) crystals as a flexible...
Guest Editorial of Virtual Special Issue: Artificial Intelligence?Assisted Fatigue Prediction of Engineering Materials and Structures
14/11/2024 -
ABSTRACTThis study aims to promote the resource utilization of solid waste in asphalt pavements and improve its fatigue performance. For this, phosphogypsum whisker (PSW) was used as a substitute...
Structure and properties of Fe40Mn20Cr20Ti10Al10 high-entropy alloy fabricated by mechanical alloying and spark plasma sintering
14/11/2024 -
Abstract The present work deals with the synthesis of a novel Fe40Mn20Cr20Ti10Al10 high-entropy alloy (HEA) by mechanical alloying (MA) and spark plasma sintering (SPS). The...
Aerospace, Vol. 11, Pages 944: Impact of Target Surface Building Direction on the Heat Transfer Characteristics of Additive Manufactured Impingement Systems
15/11/2024 -
Additive manufacturing (AM) is widely recognized as a prominent tool to maximize the potential of internal cooling systems for gas turbine applications. Several past studies have been undertaken in...
Design and Implementation of an AI-Based Robotic Arm for Strawberry Harvesting
15/11/2024 -
This study presents the design and implementation of a wire-driven, multi-joint robotic arm equipped with a cutting and gripping mechanism for harvesting delicate strawberries, with the goal of...
Detection of Defects in Polyethylene and Polyamide Flat Panels Using Airborne Ultrasound-Traditional and Machine Learning Approach
18/11/2024 -
This paper presents the use of noncontact ultrasound for the nondestructive detection of defects in two plastic plates made of polyamide (PA6) and polyethylene (PE). The aim of the study was to: (1)...
