Extrusión
Extrusión
Fibrous Pressure Sensor with Unique Resistance Increase under Partial Compression: Coaxial Wet‐Spun TiO2/Graphene/Thermoplastic Polyurethane Multi‐Wall Multifunctional Fiber
16/07/2025 -
TGTMW fibers are designed to show a sharp resistance increase under pressure, as the multi‐wall structure in the transition region between compressed and uncompressed areas bends and forms...
Scalable Low‐Carbon Ambient‐Dried Foam‐Like Aerogels for Radiative Cooling with Extreme Environmental Resistance
19/06/2025 -
A scalable low‐carbon ambient‐dried foam‐like aerogel with integrated radiative cooling and fire/harsh‐conditions resistance is fabricated via green ambient‐drying process without complex...
B4C/6082Al Composites Fabricated by Cyclic Extrusion and Compression: Microstructure and Mechanical Properties at Different Deformation Temperatures
30/05/2025 -
30 wt% B4C/6082Al composites are fabricated by cyclic extrusion and compression of composite powders, without prior or post sintering. The effect of deformation temperature on the microstructure...
Chemical Interaction Between Starch‐Polyvinyl Alcohol Matrix With Barley Microfibers: Structural, Barrier, and Viscoelastic Performance in Extruded Films
30/05/2025 -
ABSTRACTIn this study, the effect of microwave (MW) treatment on obtaining barley microfibers and their effect on the chemical, structural, and viscoelastic properties of films based on starch (S)...
Exceptional Thermal Conductivity in Printed Dielectrics through Compositional and Microstructural Design
23/05/2025 -
A multi‐generational compositional design creates a printable low‐loss dielectric composite that achieves over 16 W m−1 K−1. This breakthrough is enabled by thermal post‐processing, which...
Flexible Selenium Nanowires with Tuneable Electronic Bandgaps
21/05/2025 -
Nanotubes serve as effective test tubes for selenium nanowires, as their diameter precisely controls the width of the nanowires and the Se─Se bonding, resulting in a variety of different...
Traceless Photopolymerization with Non‐Pulsed Red Light Enables 3D‐Printable Cell‐Laden Hydrogels
16/05/2025 -
The paper presents a red‐light‐induced polymerization process, initiated by the FDA‐approved dye methylene blue and the cytocompatible co‐initiator triethanolamine, for fabricating hydrogels....
3D Printing of Ultrahigh Filler Content Composites Enabled by Granular Hydrogels
09/05/2025 -
A strategy for directly printing ultrahigh filler content composites is presented, whereby granular hydrogels are incorporated into rigid filler particle flow, leading to polymer‐based composites...
High‐Efficiency Large‐Area Perovskite Solar Cells via a Multifunctional Crystallization Regulating Passivation Additive
11/04/2025 -
A chlorine‐substituted aromatic polycyclic compound is introduced into perovskite solar cells to regulate perovskite crystallization, passivate various defects, and enhance hole transport at the...
Design and Evaluation of 3D‐Printed Polylactic Acid Composites Reinforced with Biodegradable Bamboo Powder and Jute Powder
28/03/2025 -
The study investigates 3D‐printed polylactic acid (PLA) composites with biodegradable bamboo and jute powder fillers. Mechanical, thermal, structural properties, and rheological behavior are...
A Novel Coating‐Extrusion Method Enabled, High Energy, Power Density, and Scalable Production in Monolithically Integrated Energy Storage Fibers
12/03/2025 -
A novel multifunctional fiber energy storage device consisting of LMO‐LTP‐AC is developed by the coating‐extrusion method. Due to the continuous preparation process, devices exhibited an...
3D Printable Self‐Healing Mineralized Hydrogels Loaded With Diclofenac Sodium: In Vitro and In Vivo Assessment
12/03/2025 -
ABSTRACTThe use of self‐healing mineralized hydrogels in 3D printing has demonstrated significant advantages, including enhanced printing accuracy and the ability to maintain high shape fidelity...
Reinforced Polymer Composite Filaments in Fused Deposition Modeling of 3D Printing Technology: A Review
03/03/2025 -
The review article highlights the advancements and potential of composite materials in fused deposition modeling 3D printing. Composite filaments offer improved mechanical properties and diverse...
Advanced 3D Food Printing with Simultaneous Cooking and Generative AI Design
26/02/2025 -
An in‐situ heating solution for 3D food printing is developed by incorporating noncontact graphene heaters as cooking sources during the printing process. This technique ensures food quality...
Multi‐material Volumetric Bioprinting and Plug‐and‐play Suspension Bath Biofabrication via Bioresin Molecular Weight Tuning and via Multiwavelength Alignment Optics
26/02/2025 -
Multimaterial volumetric and embedded extrusion bioprinting of complex cell‐laden architectures is enabled by unravelling the interplay between molecular weight and degree of functionalization in...
A 3D Bioprinted Gelatine‐Based Bilayer Hydrogel Dressing Loaded With Curcumin and Ciprofloxacin Hydrochloride With Antibacterial, Anti‐Inflammatory and Antioxidative Properties
16/02/2025 -
Graphical Abstract and Lay SummarySchematic diagram of gelatin/sodium alginate bilayer hydrogels loaded with ciprofloxacin hydrochloride and curcumin.ABSTRACTSkin wound repair, a highly integrated...
Extrusion Forming, Microstructure Evolution, and Mechanical Properties of Al Core Reinforced Mg Matrix Composites
06/02/2025 -
Based on the composite extrusion process, Al core reinforced Mg matrix composites are prepared. The interface bonding of the composites is explored, and the microstructure is characterized. The...
