Extrusión

Extrusión

D8410 Standard Specification for Evaluation of Cellulosic-Fiber-Based Packaging Materials and Products for Compostability in Municipal or Industrial Aerobic Composting Facilities is a new standard now available. D8410-21
18/11/2021 - 1. Scope 1.1 This specification covers cellulosic-fiber-based packaging materials and products associated with food, landscape waste, and other compost feedstocks,...
F1545 Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges has been reapproved, available as F1545-15a(2021)
- Abstract This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges for conveying corrosive fluids. Lining material shall be made from a...
D1710 Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes has been reapproved, available as D1710-15(2021)
- Abstract This specification covers the testing and requirements of extruded and compression molded polytetrafluoroethylene (PTFE) rods and heavy-walled tubing manufactured...
D4477 Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit has been revised to D4477-21
- Abstract This specification establishes the physical requirements and test methods for extruded single-wall soffits manufactured from rigid (unplasticized) poly(vinyl...
D6713 Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) has been revised to D6713-21
- Abstract This specification covers the requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded sheet, rod and tubular...
D8366 Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF has been revised to D8366-21a
- 1. Scope 1.1 This specification covers the requirements and test methods for the material, dimensions, workmanship, and the properties of extruded sheet, rod and...
D7310 Standard Practice for Defect Detection and Rating of Plastic Films Using Optical Sensors has been revised to D7310-21
- Significance and Use 4.1 Defects in film are not acceptable to the end-user as there is a reduction in the fitness-for-use in many applications. This document is intended to be...
D3222 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials has been revised to D3222-21
- Abstract This specification covers melt processable unmodified poly(vinylidene fluoride) (PVDF) molding, extrusion and coating materials. This specification covers only...
D3307 Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials has been revised to D3307-21
- Abstract This specification covers melt processable molding and extrusion materials of PFA-perfluoro(alkoxy alkane) fluorocarbon resin. The materials are copolymers of...
ISO 13775-1:2021 - Thermoplastic tubing and hoses for automotive use — Part 1: Non-fuel applications
01/09/2021 - This document specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered by internal-combustion engines, excluding use in air...
ISO 14030-4:2021 - Environmental performance evaluation — Green debt instruments — Part 4: Verification programme requirements
01/09/2021 - This document specifies requirements for verification bodies performing verification of claims of conformity to ISO 14030-1 or ISO 14030-2 and to ISO 14030-3 or a suitable substitute...
F1504 Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation has been revised to F1504-21
- Abstract This specification covers the material, dimensional, and requirements and corresponding test methods for folded poly(vinyl chloride) (PVC) pipes suitable for the...
D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials has been revised to D3350-21
- Abstract This specification covers the identification of polyethylene plastic pipe and fitting materials. Cell classification of materials shall be according to tests of...
D6779 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) has been revised to D6779-21
- 1. Scope 1.1 This classification system covers polyamide materials suitable for molding and extrusion. Some of these compositions are also suitable for application from...
D4549 Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS) has been reapproved, available as D4549-15(2021)
- Abstract This specification, which covers polystyrene materials, both crystal and rubber modified suitable for molding and extrusion, is intended to be a means of calling...
D2116 Standard Specification for FEP Resin Molding and Extrusion Materials has been reapproved, available as D2116-16(2021)
- Abstract This specification covers melt-processible molding and extrusion materials of FEP-fluorocarbon resin, which is a copolymer of tetrafluoroethylene and...
ISO 12017:2021 - Plastics — Poly(methyl methacrylate) double- and triple-skin sheets — Test methods
01/06/2021 - This document specifies the test methods for quality control of poly(methyl methacrylate) (PMMA) extruded double- and triple-skin flat sheets, obtained from colourless and coloured transparent,...
ISO 14631:2021 - Extruded sheets of impact-modified polystyrene (PS-I) — Requirements and test methods
01/06/2021 - This document specifies the requirements and test methods for solid flat extruded sheets of impact-modified polystyrene (PS-I) without fillers and reinforcing materials.This document...
D955 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics has been revised to D955-21
- Significance and Use 5.1 Injection Moldingâ??In injection molding, the difference between the dimensions of a mold cavity and of the molded specimen may vary according to the...
D3641 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials has been revised to D3641-21
- Significance and Use 5.1 It is well known that plastic test specimens molded under different conditions can have significantly different properties. This practice is designed...