Eléctrico
Eléctrico
Composite Nanoarchitectonics of TiO2/SiO2‐Loaded Rare‐Earth Metal Coordinated Prussian Blue Analog Composites for Enhanced Electroresponsive Performance
09/03/2026 -
The electrorheological response behavior of the electrorheological fluid based on TiO2/SiO2‐loaded rare‐earth metal coordinated Prussian blue analogs (PBAs) composites is investigated. The...
Synergistic Passivation Enables 22.76%‐Efficiency Quasi‐2D Perovskite Solar Cells
09/03/2026 -
Quasi‐2D ACI perovskites promise enhanced stability over 3D analogues but are still limited by defects and suboptimal Fermi‐level alignment. Multi‐site coordination of acetic anhydride steers...
Highly Conductive Ag Flakes‐Based Bio‐Adhesive for Multi‐Functional Epidermal Electronics
09/03/2026 -
A supramolecular polymer‐based biocompatible conductive ink enables in situ fabrication of skin‐conforming bioelectronics by simultaneously achieving high conductivity and strong skin adhesion,...
Low‐Dimensional MOF Nanoarchitectonics: Progress in MOF‐2D Material Hybrid Architectures for Energy Conversion and Storage
09/03/2026 -
This review highlights the integration of metal‐organic frameworks (MOFs) and two‐dimensional (2D) materials through dimensional interface engineering. By addressing intrinsic limitations like...
Piezoresistive Monitoring of Carbon Nanomaterial‐Reinforced Epoxy Composites Under Cyclic and Fatigue Loading: A Review
07/03/2026 -
Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares...
Controlled Evaporation Induced Scalable Fabrication of Reduced Graphene Oxide Thin Film: Role of Sheet Size on Its Thermal and Wetting Properties
07/03/2026 -
Scalable and reduced large‐sized graphene oxide (rLGO) films were fabricated via the doctor blade casting method. The influence of sheet size on the water wettability and thermal conductivity of...
Optimizing Post Friction Stir Welding Heat Treatment in Dissimilar Friction Stir Welded 6061/AlSi10MgMn Joints for Electrical Vehicle Battery Housing
04/03/2026 -
Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld...
Microfluidic device for electromembrane extraction with a micro-pillar stabilized liquid membrane
-
Electromembrane extraction (EME) is a microextraction technique where charged analytes are transferred across a liquid membrane, under the influence of an electrical field, and enables selective...
Electric Method for the Desulfation of Polysaccharides From Red Microalgae (Porphyridium cruentum) Cultures
07/03/2026 -
A non‐destructive method for depleting sulfates from the red microalgae Porphyridium cruentum by directly exposing the growth medium to a moderate electric field has been developed. The reported...
Activating a Metallization Switch for Record Hydrogen Evolution in Single‐Atom Modified Polar MOF Piezocatalysts
04/03/2026 -
ABSTRACTPiezocatalytic hydrogen evolution enables the conversion of mechanical energy into chemical fuels, but its efficiency is constrained by a trade‐off between piezoelectric polarization and...
Recent Advances of 2D MXene in Field‐Effect Transistors
28/02/2026 -
MXenes are emerging two‐dimensional materials for post‐Moore field‐effect transistor technologies, offering complementary metallic and semiconducting properties. Metallic MXenes enable...
Scalable and Customizable Single‐Atom Coatings for pH‐Universal H2O2 Electrosynthesis
27/02/2026 -
A universal one‐step soot‐deposition route was developed to convert various metal‐containing paraffins into conformal single‐atom catalyst (SAC) coatings on diverse electrodes, yielding...
Redox Cascade‐Driven Structural Degradation Under Reverse Bias in All‐Perovskite Tandem Solar Cells
27/02/2026 -
Unveiling a previously overlooked redox‐coupled vertical degradation pathway. Clarifying the complex Sn‐Pb perovskite degradation in tandems. Establishing an effective strategy for...
Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics
21/02/2026 -
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and...
