Transporte
Transporte
Current Trends in Multifunctional Nanocomposite Coatings through Electrodeposition for Aerospace and Strategic Defense
10/06/2025 -
A review of 2D material integrated nanocomposite coatings that substantially reduce corrosion rates (450 W m−1 K−1 (around 50%), while concurrently achieving up to 75% reduction in...
Titanium‐S23: A New Alloy with Ultra‐High Tensile Toughness Directly from the Solid‐State Processing of Recycled Ti–6Al–4V and Ti–5Al–5Mo–5V–3Cr Powders using Field Assisted Sintering Technology
10/06/2025 -
This study explores combining two existing aerospace titanium alloy powders, processing them via field‐assisted sintering technology and the subsequent discovery of a novel alloy composition,...
Effect of Low‐Frequency Vibration on the Tribological Properties of Thin‐Walled Inconel 601 with Laser Wire Additive Manufacturing
10/06/2025 -
This study demonstrates that low‐frequency vibration (0–100 Hz) during laser wire additive manufacturing significantly refines grains (31.21% size reduction), enhances surface hardness...
Influence of Temperature on Scratch and Wear Properties of Technical Thermoplastics: Implications for Material Selection
10/06/2025 -
The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics...
Entropy Analysis of Al2O3–TiO2/H2O Hybrid Nanofluid Flow over an Exponential Stretching Sheet with Thermal Dissipation and Chemical Reactions
08/06/2025 -
This study presents valuable perspectives that can be applied to various sectors, ranging from thermal engineering to nanotechnology and fluid dynamics. The practical implications of these...
Effect of High Thermal Conductive Channel on Interlaminar Shear Strength and Failure Mechanism of C/SiC Composites
29/05/2025 -
Shear fracture in high thermal conductivity channels (HTC)‐C/SiC composites involves HTC pull‐out/debonding and pitch‐fiber tearing. Bending‐shear stress coupling fractures HTCs (nearly equal...
Ultralight and Elastic Polyimide Microtube Aerogel via Airflow‐Induced Spinning
27/05/2025 -
This paper reports the one‐step preparation of ultralight polyimide microtube aerogel sponges (PMAS) using airflow‐induced spinning. PMAS has ultralow density, excellent thermal insulation...
Untying the Knot: A Fully Recyclable, Solvent‐Free, Wide‐Spectral Photocurable Thermoset Adhesive
16/05/2025 -
This study introduces a solvent‐free, recyclable adhesive that cures rapidly under visible light (400–650 nm) while maintaining robust adhesion across diverse substrates. Recyclable via simple...
High‐Entropy Alloys for Next‐Generation Electromagnetic Shielding Applications
06/05/2025 -
This review presents high‐entropy alloys as advanced EMI shielding materials, showcasing their diverse forms and key advantages—corrosion resistance, thermal stability, mechanical strength, and...
Patterned Design of the Electric Heating Element Achieves Efficient Joule Heating
29/04/2025 -
This study addresses the challenges associated with traditional electric heating elements used in aerospace deicing systems, specifically their low thermal conductivity, poor high‐temperature...
Reduction in Coefficient of Thermal Expansion of Cu‐Based Self‐Lubricating Composites without Decreasing Wear Resistance by the Addition of Ni50Fe
20/04/2025 -
This article aims to match the thermal expansion coefficient (CTE) of Cu‐based self‐lubricating composites with steel by adding Ni50Fe. A composite with 40 vol% Ni50Fe achieves a 13.7% lower...
Reinforced Polymer Composite Filaments in Fused Deposition Modeling of 3D Printing Technology: A Review
03/03/2025 -
The review article highlights the advancements and potential of composite materials in fused deposition modeling 3D printing. Composite filaments offer improved mechanical properties and diverse...
Stereoisomerism of Vicinal Polydichloronorbornene for Ultra‐High‐Temperature Capacitive Energy Storage
03/03/2025 -
Stereoisomerism engineering plays a crucial role in tailoring the properties of vicinal dichloronorbornene (PDCNB), with profound effects in backbone spacing, π‐stacking, barrier height, and trap...
Optimization and Comparative Analysis of Machining Performance of Al–Cu–SiC–GNP Composite: Influence of Reinforcement Variations Using Machine Learning, RSM, and ANOVA Validation
14/02/2025 -
This study optimizes the machinability of composites via stir casting using machine learning, response surface methodology, and ANOVA. The effects of SiC and GNP reinforcements on material removal...
Oxide‐Based Ceramic Matrix Composites for High‐Temperature Environments: A Review
11/02/2025 -
This review examines oxide‐based ceramic matrix composites, focusing on their processing, composition, and mechanical properties for high‐temperature applications. Key topics include oxidation...
Designing and Fabrication of a Biomimetic Soft Gripper Utilizing Phase Transition 3D Printing Technology
10/02/2025 -
A bimaterial flexible soft gripper is fabricated using magnetic rheological fluid and silicone via dual‐material printing. It grasps by leveraging variable stiffness and negative pressure,...
Multimaterial Bonding of Additively Manufactured Carbon Fiber‐Reinforced Thermoplastics/64 Titanium
05/02/2025 -
A multimaterial technique for directly bonding carbon‐fiber‐reinforced thermoplastics to titanium alloy substrates is developed using a fused filament fabrication 3D printer, and a maximum shear...
Harnessing 3D Porous Cobalt Oxide Nanoflakes Grown on Metal for Exceptional Adhesion between Aluminum Surfaces and the Epoxy Matrix
13/01/2025 -
This study demonstrates the possibility of enhancing the adhesion strength between two metal surfaces by growing 3D porous cobalt oxide nanoflakes on their porous surfaces. In addition, using...
Development of a Novel Processing Route for Dispersoid/Precipitation‐Strengthened High Conductive Copper Alloys by Using Metalized Nanoceramics in Additive Manufacturing
24/12/2024 -
This study explores a process chain to produce dispersoid‐strengthened CuCr1Zr for applications requiring high strength and conductivity. Using gas‐atomized powder and copper‐plated alumina...
Impact of human activities on the long-term change and seasonal variability of Ebinur Lake, Northwest China
11/12/2025 -
Abstract The Triple Ionosphere PhotoMeter (TRIPM) is a far ultraviolet nadir-view photometer that is onboard the second-generation, polar-orbiting Chinese meteorological satellite...
Separation of the ionospheric and thermospheric contributions in the data from the Triple Ionosophere PhotoMeter onboard the Feng-Yun 3E satellite
01/12/2025 -
Abstract Purpose of Review Endoscopic submucosal dissection (ESD) has been found to increase en bloc and R0 resection as well...
